manualshive.com logo in svg

OTE Speedport Entry 2i, Maintenance Management Manual

Share
Download
OTE Speedport Entry 2i Maintenance Management Manual Download Page 71

SJ-20162405182123-002|2016-05-24 (R2.0) 

 

 

 

 

Configure the Local Network 

 

 

4-19

 

 

 

 

 

 

Figure 4-23 Policy Routing (IPv6) Page

 

 

 

 

17.  Configure the Policy Routing  parameters. 

Table 4-15 

lists the Policy Routing 

parameters. 

Table 4-15 Parameter Descriptions for the Policy Routing (IPv6)

 

 

Parameter

 

Description

 

Name 

The name of Policy routing  entry. 

WAN Connection 

WAN connection for policy routing 

Source IP 

Source IPv6 address of the matching packets. 

Destination IP 

Destination IPv6 address of the matching packets. 

Protocol 

Matching IPv6 protocol. The ANY option means any  IPv6 

protocol. 

Source Port 

Source port number of the matching packets. 

Destination Port 

Destination port number of the matching packets. 

Source MAC 

MAC address of the source device that sends the  matching 

packets. 

 
 

 

 

The 

Policy Routing 

configuration options vary with the 

Protocol 

value. 

 

 

 

18.  Click 

Apply 

button to apply the  changes. 

– End of Steps  – 

Note: 

Summary of Contents for Speedport Entry 2i




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands