background image

 

PNSPO!

 
 

Model 

F39-MC11

(ver. 3)

 

 

Setting Console 

 

 

 INSTRUCTION  MANUAL

           

 

 
 
 
Thank you for selecting OMRON product. This manual primarily 
describes precautions required in installing and operating the product. 
Before operating the product, read this manual thoroughly to acquire 
sufficient knowledge of the product. For your convenience, always keep 
this manual at hand. 
 
 
 
 
 
 
 
 
 
 

                             

 

©OMRON Corporation 2001-2003 All Rights Reserved. 

 
 
 

                                                                     

 

 

 

i

Read and Understand this Instruction Manual 

Please read and understand this instruction manual before storing, 
installing, programming, operating, maintaining, or disposing of the 
products.  Please consult your OMRON representative if you have any 
questions or comments.     
 
 

Warranty, Limitations of Liability 

WARRANTY

 

OMRON's exclusive warranty is that the products are free from 
defects in materials and workmanship for a period of one year (or 
other period if specified) from date of sale by OMRON. 
 
OMRON MAKES NO WARRANTY OR REPRESENTATION, 
EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, 
MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE 
OF THE PRODUCTS.    ANY BUYER OR USER ACKNOWLEDGES 
THAT THE BUYER OR USER ALONE HAS DETERMINED THAT 
THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF 
THEIR INTENDED USE.  OMRON DISCLAIMS ALL OTHER 
WARRANTIES, EXPRESS OR IMPLIED.     

LIMITATIONS OF LIABILITY

 

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, 
INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS 
OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE 
PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, 
WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.     
 
In no event shall the responsibility of OMRON for any act exceed the 
individual price of the product on which liability is asserted.     
 
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR 
WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE 
PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE 
PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, 
AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, 
ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR 
REPAIR.   

 
 

Summary of Contents for F39-MC11




































Reviews: