Obihai OBi100 Administration Manual Download

Page: 161 / 220

161

Priority

Priority assigned to this codec (1 is the highest)

PayloadType

Standard payload type for G711-alaw
Note: Informational only; not configurable

G729 Codec

Codec

Codec Name

G729

BitRate

Bit rate in bits/sec
Note: Informational only; not configurable

8000

Enable

Enable this codec

Yes

SilenceSuppression

Enable silence suppression for this codec

PacketizationPeriod

Packet size in ms

Priority

Priority assigned to this codec (1 is the highest)

PayloadType

Standard payload type for G.729
Note: Informational only; not configurable

G726R32 Codec

Codec

Codec Name

G726-32

BitRate

Bit rate in bits/sec
Note: Informational only; not configurable

32000

Enable

Enable this codec

Yes

SilenceSuppression

Enable silence suppression for this codec

PacketizationPeriod

Packet size in ms

Priority

Priority assigned to this codec (1 is the highest)

PayloadType

Dynamic Payload type for this codec. Valid range is 96-127

104

G726R16 Codec

Codec

Codec Name

G726-16

BitRate

Bit rate in bits/sec
Note: Informational only; not configurable

16000

Enable

Enable this codec

Yes

SilenceSuppression

Enable silence suppression for this codec

PacketizationPeriod

Packet size in ms

Priority

Priority assigned to this codec (1 is the highest)

PayloadType

Dynamic Payload type for this codec. Valid range is 96-127

102

G726R24 Codec

Codec

Codec Name

G726-24

BitRate

Bit rate in bits/sec
Note: Informational only; not configurable

24000

Enable

Enable this codec

Yes

SilenceSuppression

Enable silence suppression for this codec

PacketizationPeriod

Packet size in ms

Priority

Priority assigned to this codec (1 is the highest)

PayloadType

Dynamic Payload type for this codec. Valid range is 96-127

103

G726R40 Codec

Codec

Codec Name

G726-40

BitRate

Bit rate in bits/sec
Note: Informational only; not configurable

40000

Enable

Enable this codec

Yes

SilenceSuppression

Enable silence suppression for this codec

PacketizationPeriod

Packet size in ms

Priority

Priority assigned to this codec (1 is the highest)

G726R16, G726R24, and G726R40 codecs are only available only on the OBi100/110; iLBC codec is only available on the

OBi200/OBi202/OBi300/OBi302

Summary of Contents for OBi100









































































































































































































Search results

Summary of Contents for OBi100

Reviews:

Related manuals for OBi100

Brands by name

Popular brands

Obihai OBi100, Administration Manual

Search results

Summary of Contents for OBi100

Reviews:

Related manuals for OBi100

Brands by name

Popular brands