manualshive.com logo in svg

Nuvoton NuMicro M0A21 Series, Technical Reference Manual

Share
Download
Nuvoton NuMicro M0A21 Series Technical Reference Manual Download Page 464

            M0A21/M0A23 Series 

 

May 06, 2022 

Page 

464

 of 746 

Rev 1.02 

M0

A21

/M
0

A

2

3

 SE
RIES

 TEC

H

NICAL 

RE
FEREN

C

E 
M

ANUAL

 

1. 

0 = No RDA interrupt is generated. 

1 = RDA interrupt is generated. 

[7] 

LINIF 

LIN Bus Interrupt Flag 

This  bit  is  set  when  LIN  slave  header  detect  (SLVHDETF  (UART_LINSTS[0]  =  1)),  LIN 
slave  header  error  detect  (SLVHEF  (UART_LINSTS[1]  =  1)),  LIN  slave  ID  parity  error 
(SLVIDPEF  (UART_LINSTS[2]  =  1)),  LIN  slave  header  time-out  detect  (SLVHTOF 
(UART_LINSTS[4] = 1)), LIN response time-out detect (RTOUTF (UART_LINSTS[5] = 1)), 
LIN  break  detect  (BRKDETF  (UART_LINSTS[8]  =  1)),  or  bit  error  detect  (BITEF 
(UART_LINSTS[9] = 1)). If LINIEN (UART_INTEN[8]) is enabled the LIN interrupt will be 
generated. 

0  =  None  of  SLVHDETF,  SLVHEF,  SLVIDPEF,  SLVHTOF,  RTOUTF,  BITEF,  and 
BRKDETF is generated. 

1 = At least one of SLVHDETF, SLVHEF, SLVIDPEF, SLVHTOF, RTOUTF, BITEF, and 
BRKDETF is generated. 

Note:

  This  bit  is  cleared  when 

SLVHDETF 

(UART_LINSTS[0]),  SLVHEF 

(UART_LINSTS[1]),  SLVIDPEF  (UART_LINSTS[2]),  SLVHTOF  (UART_LINSTS[4]), 
RTOUTF 

(UART_LINSTS[5]), 

BRKDETF 

(UART_LINSTS[8]), 

and 

BITEF 

(UART_LINSTS[9]) all are cleared and software writing ‘1’ to LINIF (UART_INTSTS[7]). 

[6] 

WKIF 

UART Wake-up Interrupt Flag (Read Only) 

This  bit  is  set

 

when  TOUTWKF  (UART_WKSTS[4]),  RS485WKF  (UART_WKSTS[3]), 

RFRTWKF 

(UART_WKSTS[2]), 

DATWKF 

(UART_WKSTS[1]) 

or 

CTSWKF 

(UART_WKSTS[0]) is set to 1. 

0 = No UART wake-up interrupt flag is generated. 

1 = UART wake-up interrupt flag is generated. 

Note:

  This  bit  is  cleared  if  all  of  TOUTWKF,  RS485WKF,  RFRTWKF,  DATWKF  and 

CTSWKF are cleared to 0 by writing 1 to the corresponding interrupt flag.

 

[5] 

BUFERRIF 

Buffer Error Interrupt Flag (Read Only) 

This bit is set when the TX FIFO or RX FIFO overflows (TXOVIF (UART_FIFOSTS[24]) or 
RXOVIF  (UART_FIFOSTS[0])  is  set).  When  BUFERRIF  (UART_INTSTS[5])  is  set,  the 
transfer  is  not  correct.  If  BUFERRIEN  (UART_INTEN[5])  is  enabled,  the  buffer  error 
interrupt will be generated. 

0 = No buffer error interrupt flag is generated. 

1 = Buffer error interrupt flag is generated. 

Note:

  This  bit  is  cleared  if  both  of  RXOVIF  (UART_FIFOSTS[0])  and  TXOVIF 

(UART_FIFOSTS[24]) are cleared to 0 by writing 1 to RXOVIF (UART_FIFOSTS[0]) and 
TXOVIF (UART_FIFOSTS[24]). 

[4] 

RXTOIF 

RX Time-out Interrupt Flag (Read Only) 

This bit is set when the RX FIFO is not empty and no activities occurred in the RX FIFO 
and  the  time-out  counter  equal  to  TOIC  (UART_TOUT[7:0]).  If  RXTOIEN 
(UART_INTEN[4]) is enabled, the RX time-out interrupt will be generated. 

0 = No RX time-out interrupt flag is generated. 

1 = RX time-out interrupt flag is generated.  

Note:

 This bit is read only and user can read UART_DAT (RX is in active) to clear it. 

[3] 

MODEMIF 

MODEM Interrupt Flag (Read Only) 

This bit is set when the nCTS pin has state change (CTSDETF (UART_MODEMSTS[0]) 
= 1). If MODEMIEN (UART_INTEN[3]) is enabled, the Modem interrupt will be generated. 

0 = No Modem interrupt flag is generated. 

1 = Modem interrupt flag is generated. 

Note:

 This bit is read only and reset to 0 when bit CTSDETF is cleared by a write 1 on 

CTSDETF (UART_MODEMSTS[0]). 

[2] 

RLSIF 

Receive Line Interrupt Flag (Read Only)   

This bit is set when the RX receive data have parity error, frame error or break error (at 
least  one  of  3  bits,  BIF  (UART_FIFOSTS[6]),  FEF  (UART_FIFOSTS[5])  and  PEF 
(UART_FIFOSTS[4]), is set). If RLSIEN (UART_INTEN[2]) is enabled, the RLS interrupt 

Summary of Contents for NuMicro M0A21 Series











































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands