NTT docomo FOMA D701I, Manual

Page: 298 / 517

i-
α
pp
li
295
Operating i-
α
ppli Stand-by Display
i-
α
ppli Stand-by Display
When i-
α
ppli is set for the stand-by display, you can start i-
α
ppli from the stand-by display to operate.
or is indicated when the i- α ppli stand-by display is set.
･
It is necessary to set i-
α
ppli for the stand-by display beforehand.
☛
P122
Starting i-
α
ppli of the i-
α
ppli stand-by display
To start i-
α
ppli set on the i-
α
ppli stand-by display, switch the i-
α
ppli stand-by display to the i-
α
ppli
screen.
･
You cannot start i-
α
ppli when Lock on Close is set to on.
1
Press
c
on the i-
α
ppli stand-by display.
The screen is changed to the i-
α
ppli screen and or flashes at the top of the screen.
INFORMATION
● If the i-
α
ppli you attempt to start with i-
α
ppli To is not saved in FOMA terminal, the message that there is
no specified i-
α
ppli is displayed and i-
α
ppli cannot be started. Note that some i-
α
ppli may start just after
downloaded from sites even if it is not saved.
･
For i-
α
ppli that starts just after downloaded from sites, a confirmation screen may be displayed asking
whether to make communication while it is activated.
･
When ending i-
α
ppli that started just after downloaded from sites, a confirmation screen is displayed
asking whether to save i-
α
ppli. Note that some i-
α
ppli may not be able to be saved in FOMA terminal.
● If the specified i-
α
ppli is set not to start with i-
α
ppli To, a message is displayed and i-
α
ppli is not started.
☛
P288
● i-
α
ppli can also be started by using the infrared communication and Bar Code Reader.
INFORMATION
●
When FOMA terminal is turned on while setting i- α ppli Stand-by Display, a confirmation screen is
displayed asking whether to start the i- α ppli stand-by display. When you select Yes , the i- α ppli stand-by
display starts. When you select No , the i- α ppli stand-by display settings are canceled. If you operate
nothing within about 5 seconds after the confirmation screen has appeared, the i- α ppli stand-by display
starts automatically. When the power is turned on by Auto Power ON, the i- α ppli stand-by display
automatically starts, without displaying the confirmation screen.
●
When you set i- α ppli that performs communication, it may not operate correctly depending on radio wave
conditions, etc.
●
i- α ppli stand-by display does not operate while Privacy Mode is on ( Authorized access set for i- α ppli ).
●
If you activate All Lock or PIM Lock while the i- α ppli stand-by display is set, the i- α ppli stand-by display is
temporarily canceled. When you cancel lock, the i- α ppli stand-by display starts again.
●
If the use of i- α ppli set to the i- α ppli stand-by display is stopped by IP (Information service provider), the
i- α ppli standby display is canceled.
●
Even when i- α ppli Stand-by Display is specified, if stand-by tickers are displayed due to signals from IP
(Information service provider), the i- α ppli Stand-by Display settings may be canceled.
●
While the i- α ppli stand-by display is activated, if an error occurs that makes it difficult for the i- α ppli stand-
by display to continue to appear, a confirmation screen is displayed asking if you will cancel or not. When
you select Yes , the i- α ppli stand-by display settings are canceled. At this time, the name of i- α ppli and end
date/time are recorded in Abnormal Exit History.
●
You cannot connect to a site (Web To) from the i- α ppli stand-by display.
Next