NTT docomo FOMA D701I, Manual

Page: 428 / 517

Data Co
mm
unic
a
tio
n
425
The dialup communication (APN) for packet
communication can be set for registration numbers
between cid1 to 10 in FOMA terminal. By default,
“mopera.ne.jp” is set for cid1 and “mopera.net” for
cid3. This setting is not required for mopera U /
mopera. When connecting to any other service
provider or to an in-house LAN, be sure that the
dialup connection (APN) is registered either at cid2 or
at anything from cid4 to cid10.
･
For the dialup connection (APN), inquire your
provider or network administrator.
･
The dialup connection settings can be considered
as phonebook registration for packet
communication. The comparison between dialup
connection settings and the FOMA terminal
phonebook is as follows:
･
The registered cid become the connection numbers
of dialup connection setting.
Setting show/hide caller ID
Take care when disclosing your caller ID since it is
important information.
･
Settings must be “Show” for using mopera U /
mopera.
1 Perform Steps 1 to 5 of “Setting dialup
connection (APN) for packet
communication”.
☛
P424
2 Set show (186)/hide (184) caller ID during
packet communication.
Enter in the format “AT ＊ DGPIR=<n>”.
3 Check that
OK
is displayed and click
ファ
イル , ハイパーターミナルの終了 .
･
“XXX”
と名前付けされた接続を保存しますか
?
is displayed. Click
いいえ
.
■
Setting to show/hide caller ID by dialup
network settings
The dialup network settings can also be used
to append “186 (show)” or “184 (hide)” to the
dialup connection number.
If “186” (show) or “184” (hide) is set by both
the AT
＊
DGPIR command and dialup
network settings, the show/hide caller ID
setting is as shown below:
･
To reset the show/hide setting made by the
AT
＊
DGPIR command to the default (not
set), enter “AT ＊ DGPIR=0”.
Setting for Windows XP
Use the network connection wizard to set the dialup
connection and TCP/IP protocol.
1 Click スタート , すべてのプログラム , ア
クセサリ
,
通信
and
ネットワーク接続
.
ネットワーク接続
screen is displayed.
2 Click
新しい接続を作成する
(Create new
connection) in ネットワークタスク
(Network task).
新しい接続ウィザード
(New connection wizard)
screen is displayed.
3
Click
次へ
.
A screen for selecting the type of network
connection is displayed.
4 Select
インターネットに接続する
(Connect to Internet) and click 次へ .
The setup screen is displayed.
5 Select 接続を手動でセットアップする
(Set up connection manually) and click
次
へ
.
The Internet connection screen is displayed.
Dialup connection (APN) and
registration number (cid)
Default not set
AT ＊ DGPIR=1 ：
When packet communication connection is
being established, “184” is added to connect
to the dialup connection (APN).
AT ＊ DGPIR=2 ：
When packet communication connection is
being established, “186” is added to connect
to the dialup connection (APN).
Dialup connection
settings
FOMA terminal phonebook
entries
Registration
number (cid) Registration number (Phonebook
No.)
APN Party’s phone number
Setting dialup connection
Show/hide caller ID setting
made by AT ＊ DGPIR
command
Dialup network
setting (<cid>=1)
not set Hide Show
＊ 99 ＊＊＊ 1#
Caller
ID is
sent.
Caller
ID is
not
sent.
Caller
ID is
sent.
184 ＊ 99 ＊＊＊ 1#
Caller ID is not sent.
186
＊
99
＊＊＊
1#
Caller ID is sent.
Next