Novus NHDR-4304AHD User Manual Download Page 47

Page: 47 / 124

NHDR

4xxxAHD user’s manual ver. 1.1

ALARMS

There are buttons in the bottom right corner:

Alarm

Motion

opens a separate action or detection settings window.

Copy

copies selected parameters of one camera to anothers.

Default

restores the default settings of this screen.

Apply

saves all settings.

7.2. Alarm inputs

The

submenu contains settings for responding to changes in the status of alarm inputs in DVR and

Novus 2000 and 4000 series IP cameras.

The table columns are described below. Some columns may not be visible, to see them you need to
move the scroll bar at the bottom of the screen:

Alarm In

number of alarm input.

Local

means alarm input on the recorder,

IP CH

means alarm input

on IP camera.

Alarm type

specify the type of alarm input:

Normally

Open

high state activation,

Normally

Closed

low state activation, or

OFF

inactive.

Buzzer

duration time of sound alarm after detection (

Disable

10s

20s

40s

60s

Alarm Out

enable alarm output. It is possible to change alarm output status on the recorder

(

Local

) or in Novus 2000 or 4000 series IP camera (eg.

IP K.1

Latch Time

time of the alarm output duration:

10s

20s

40s

60s

Channel

switching on the video stream recording when the alarm input is activated (it depends on the

recording schedule settings). It is possible to set the recording of multiple cameras to an event from
a

single alarm input.

Post Recording

defines the time of active alarm after the alarm ends:

10s

15s

20s

30s

1min

2min

5min

. It also specifies full screen display and alarm recording time.

Show Message

displays the icon on the screen when the alarm input is activated.

Send email

send an e

mail message when an alarm occurs. The camera image will be sent as

attachment. Requires e

mail configuration in the

Network / Email

menu.

Full screen

displays the camera image in full screen mode when the alarm input is activated.

Summary of Contents for NHDR-4304AHD





























































































































Search results

Summary of Contents for NHDR-4304AHD

Reviews:

Novus NHDR-4304AHD, User Manual, Page: 47 / 124

Search results

Summary of Contents for NHDR-4304AHD

Reviews: