manualshive.com logo in svg

Novus NHDR-4304AHD, User Manual, Page: 15 / 124

Share
Download
Novus NHDR-4304AHD User Manual Download Page 15

NHDR

-

4xxxAHD user’s manual ver. 1.1

 

All rights reserved © AAT Holding S.A. 

 

 

15

 

FIRST LAUNCH WIZARD

 

Free / Total 

-

 information about free and total HDD space.

 

Free / Total Time

 

-

 estimated time of recording, which should be recorded on the free hard disk space 

and the total recording time. The time depends on the encoding and the amount of video frames. 

 

Overwrite

 

-

 the default 

Auto 

setting cause recordings overwriting from the oldest when there is no free 

space on HDDs. When overwriting is 

OFF

, the DVR will stop recording when the disk is full. It is also 

possible to set the time after which recordings will be overwritten: 

1

 

day,  3  days,  7  days,  14  days,

 

30 days 

and 

90 days

. It means the longest time of stored recordings, after which the recordings will be 

deleted.

 

Format HDD

 

-

 formatting the hard disk. Select the HDD before it.

 

Caution! You need to format the disk to start recording. Formatting deletes all data permanently 
from the hard disk.

 

 

2.7. Monitor output resolution

 

The next section allows to select the monitor output resolution. Following HDMI output resolutions are 
supported:  1024x768,  1280x1024,  1440x900,  1280x720,  1920x1080,  1680x1050,  1600x1200, 
1920x1200, 3840x2160. VGA output supports resolutions up to 1920x1080.

  

 

Press  the 

Apply

  button  after  selecting  the  resolution.  When  you  change  the  resolution,  you  are 

prompted  to  confirm  the  change.  If  the  change  is  not  confirmed  within  20  seconds,  the  previous 
resolution is reverted.

 

Note!  During  the  first  launch  the  image  resolution  on  the  HDMI  and  VGA  outputs  is  set  to 
1280x1024.

 

 

2.8. P2P identifier

 

DVR allows to connect over the Internet using P2P service. The connection to the recorder is done by 
an external server, even if the recorder does not have a public IP address. The recorder need Internet 
access  only.  The  connection  to  the  DVR  via  the 

P2P  ID 

is  available  from  the  NHDR

-

5000viewer 

software or Rxcamview application. 

 

Summary of Contents for NHDR-4304AHD





























































































































Reviews:

No comments