Novatel DL-V3 Reference Manual Download Page 78 | Manualshive

Page: 78 / 116

background image

78

DL-V3 Firmware Reference Manual Rev 2

Chapter 3

DL-V3 Logs

3.2

CURRENTSET

CURRENTFILE/CURRENTGROUP

Configuration

The CURRENTSET log contains the current file, current filetransfer packet, current file dumpmode,
and current group setting for the receiver.

Structure:

Message ID = 187

Log Type: Polled

Continued on Page 78

16-17

Reserved

18

GENERIC

The port accepts/generates nothing. SEND/SENDHEX
commands from another port generate data on this port.
Any incoming data on this port can be seen with
PASSCOM logs on another port, refer to the

OEMV

Family Firmware Reference Manual.

a. An output interfacemode of RTCMNOCR is identical to RTCM but with the CR/LF appended.

An input interfacemode of RTCMNOCR is identical to RTCM and functions with or without
the CR/LF.

b. CDGPS has three options for output of differential corrections - NMEA, RTCM, and GPS*C.

If you have a ProPak-V3 receiver, you do not need to use the INTERFACEMODE command
with CDGPS as the argument. The CDGPS argument is for use with obsolete external non-
NovAtel CDGPS receivers. These receivers use GPS*C (NavCanada’s proprietary format
differential corrections from the CDGPS service).

c. The AUX port, and therefore TAUX mode, is only available on OEMV-2-based and OEMV-3-

based products.

Binary Value

ASCII Mode Name

Description

Field

Data

Description

Bytes

Format

Units

Offset

1

Header

Log header, see

-

-

0

2

File

Current file as set by the
CURRENTFILE command,
see

Page

12

Char[ ]

-

H

3

FilePacket

Current packet as set by the
CURRENTFILE command

4

Ulong

-

H+12

4

FileDumpMode Dump

mode as set by the

CURRENTFILE command,
see

Table 8, Dump Mode

4

Enum

-

H+16

5

Group

Current group as set by the
CURRENTGROUP
command, see

12

Char[ ]

-

H+20

«
...
76
77
78
79
80
...
»

Summary of Contents for DL-V3





















































































































Reviews:

No comments

Related manuals for DL-V3

Brand: Panasonic Pages: 7

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 44

SAHE200 - RECEIVER

Brand: Panasonic Pages: 25

PressIT TY-SB01WP

Brand: Panasonic Pages: 25

Brand: TANDBERG Pages: 23

Wall Mount Adaptor 010882

Brand: CyberData Pages: 2

Brand: Reer Pages: 2

Brand: Grundig Pages: 25

Freeview TRF-7150

Brand: Topfield Pages: 78

Brand: Aventura Pages: 6

Brand: Silent Call Communications Pages: 8

Brand: Topfield Pages: 68

Brand: RF-Link Pages: 4

Digital Freeview Receiver

Brand: Tevion Pages: 2

Brand: Luxi Electronics Pages: 2

HD-RX-4K-x10-C-E

Brand: Crestron Pages: 56

Brand: JETStream Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands