Novatel DL-V3 Reference Manual Download Page 67

Page: 67 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

2.39 SITEUPDATEANTTYPE

Set Occupied Site Antenna

The

siteupdateanttype

command allows you to configure the site antenna type information (AntType

field in the

sitedef

log) once the site has been occupied (by issuing a

site enter

command).

The

siteupdateanttype

set

command sets the site antenna type for an occupied site to

anttype.

The

siteupdateanttype

default

and the

siteupdateanttype

clear

commands clear the site antenna type

for an occupied site

The

siteupdateanttype

clear

command clears the site antenna type for an occupied site

Syntax

siteupdateanttype

set [

anttype

]

siteupdateanttype

default|clear

Message ID = 168

Table 49: SITEUPDATEANTTYPE Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on

Page 41

Enum

none

Antenna type

NUL

Char[]

none

H+4

Reserved for future use

NUL

Char[]

none

H+20

Parameter

Power-On

Freset

Stored in NVM

AntType

clear

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands