Novatel DL-V3 Reference Manual Download Page 106

Page: 106 / 116

106

DL-V3 Firmware Reference Manual Rev 2

Chapter 4

DL Explorer

If do you wish to enter specific site information and have the information included in the group
definition, check the

Include Site Information

check box. The editable fields are:

Antenna Model

Enter the model number for your antenna.

Antenna Height

Enter the vertical antenna height above ground.

Antenna Number

Enter your antenna’s serial number.

Site Number

Enter a number for this site.

Site Name

Enter a site name.

If the

Site Name

field is left blank, the log file name is used as the site name.

The group definition issued during the group upload includes the GROUPANTHEIGHT,
GROUPANTSN, GROUPANTTYPE, GROUPSITENAME, and GROUPSITENUMBER. See

Pages

32, 33, 34, 50,

and

respectively for further details on these commands.

You may need to edit the following fields from their default values depending on your application:

Minimum Satellites Select a number from 1 to 9 for the minimum number of satellites,

where the default is 4.

Elevation Mask

Choose an integer value for the elevation mask angle between 0 and
90 degrees, where the default is 0.

4.2.1.5

Interfaces Tab

The

Interfaces

tab, in the

DL Groups

dialog, is shown in

Figure 8

Figure 8: Interfaces Tab

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands