Novatel DL-V3 Reference Manual Download Page 109

Page: 109 / 116

DL Explorer

Chapter 4

DL-V3 Firmware Reference Manual Rev 2

109

Figure 10: COM Parameters

Select your DL-V3’s communication port and baud rate (the defaults are COM1 and 9600
respectively) and click on the

Apply

button. Click on the

Refresh

button to update the

Port Settings

dialog with the DL-V3’s current settings. Click on the

Factory Reset

button to return all the port

settings to their factory defaults.

When connected using the USB port, the baud rate is ignored by the USB drivers and instead
the baud rate is as fast as possible.

The current highest baud rate shown in

DL Explorer

is 230400.

4.3.2

Upload Group from the PC to the Receiver

Click on the

button in the main

DL Explorer

window and the

Group Management

dialog

appears, see

Figure 11

Page 110

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands