Novatel DL-V3 Reference Manual Download Page 25

Page: 25 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

Table 7: COM Voltage Out Action

2.4

CURRENTFILE

Specify File for

FILEHDR/FILETRANSER

Logs

The

currentfile

command allows you to specify a file to which subsequent requests for

filehdr

and

filetransfer

logs apply, see

Pages 82

Specified without arguments, the

currentfile

command clears any previously configured

currentfile

settings. The

currentfile file

command:

•

Configures the

currentfile

file

File

is a name of a file on the CF card specified in a

base.ext

format, where

base

is a maximum of 8 characters and the optional

ext

is a maximum of 3

characters. Subsequent requests for the

filehdr

log, see

Page 82,

displays the

filehdr

log read from

file

. Subsequent requests for the

filetransfer

log, see

Page 84,

transfers

file

filetransfer

log

packets.

•

Issued with the dump mode specified as

all

, causes the receiver to transfer the entire file on all

subsequent requests for the

filetransfer

log.

•

Issued with the transfer mode specified as

{single [packet_id]}

, causes the receiver to transfer

only file packet number

packet_id

on all subsequent requests for the

filetransfer

log.

Packet_id

ranges from 0 to SizePackets-1, see the

dirent

log on

Page 79

. The first packet is numbered 0.

Packet size is defined in the

file

log definition.

•

Issued without specifying the dump mode, defaults the dump mode to

all

Syntax

currentfile

file

[all|{single [

packet_id

]}]

Message ID = 185

Binary

ASCII

Description

OFF

Set state to off

Set state to on

Reserved

DEFAULT

Do not change the COMVOUT state.
This option only applies to
GROUPCOMVOUT. See also the
GROUP command on

Page 30

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands