Novatel DL-V3 Reference Manual Download Page 56

Page: 56 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.28 METHUMID

Specify Air Humidity

The

methumid

command allows you to specify air humidity. Humidity specified with the

methumid

command does not affect receiver operation. Rather, it allows you to create a record of atmospheric
conditions for post-processing purposes.

The

methumid

set

command specifies air humidity at

humid

. This command only stores the humidity

value in volatile memory, and does not automatically generate a record. The humidity value can then
be displayed/recorded by requesting the

met

log.

The

methumid

clear

and the

methumid

default

commands clear the humidity setting

Syntax

methumid

set [

humid

]

methumid

default|clear

Message ID = 163

Table 37: METHUMID Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on Page 41

Enum

none

Humidity

Float

percent

H+4

Parameter

Power-On

Freset

Stored in NVM

methumid

clear

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands