Novatel DL-V3 Reference Manual Download Page 66

Page: 66 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.38 SITEUPDATEANTHEIGHT

Set Occupied Site Height

The

siteupdateantheight

command allows you to configure the site antenna height information

(AntHeight field in the

sitedef

log) once the site has been occupied (by issuing a

site enter

command).

The

siteupdateantheight

set

command sets the site antenna height for an occupied site to

antheight.

The

siteupdateantheight

default

and the

siteupdateantheight

clear

commands clear the site antenna

height for an occupied site

Syntax

siteupdateantheight

set [

antheight

]

siteupdateantheight

default|clear

Message ID = 167

Table 48: SITEUPDATEANTHEIGHT Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on Page 41

Enum

none

Antenna height

Float

none

H+4

Reserved for future use

NUL

Char[]

none

H+8

Parameter

Power-On

Freset

Stored in NVM

AntHeight

clear

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands