Novatel DL-V3 Reference Manual Download Page 29

Page: 29 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

2.9

FRESET

Clear Selected Data from NVM and Reset

The OEMV

freset

command is extended to include DL-V3 features. An additional target field,

userdata

(value = 10), resets only the DL-V3 user data NVM, thereby resetting all parameters

indicated in this document as “Stored in NVM” to factory defaults. Issuing the

freset

command with

the “target” field set to

standard

, resets the userdata NVM as well as OEMV parameters as indicated

in the

OEMV Family Firmware Reference Manual

The DL-V3 factory default command list is on

Page 31

If you issue the FRESET command without any parameters, it is the same as issuing a FRESET
STANDARD command.

Table 13: FRESET Target

Field

Field
Type

ASCII
Value

Binary

Value

Description

Binary

Format

Binary

Bytes

Binary

Offset

FRESET
header

This field contains the command
name or the message header
depending on whether the
command is abbreviated ASCII,
ASCII or binary, respectively.

target

See

Table 13

Data to be reset by the receiver

Enum

Binary

ASCII

Description

STANDARD

Resets commands, ephemeris, and almanac
(default). Also resets all L-Band related data except
for subscription information.

COMMAND

Resets the stored commands (saved configuration)

GPSALMANAC

Resets the stored GPS almanac

GPSEPHEM

Resets the stored GPS ephemeris

GLOEPHEM

Resets the stored GLONASS ephemeris

MODEL

Resets the currently selected model

USERDATA

Reset DL-V3-only commands

CLKCALIBRATION

Resets the parameters entered using the
CLOCKCALIBRATE command

SBASALMANAC

Resets the stored SBAS almanac

LAST_POSITION

Resets the position using the last stored position

GLOALMANAC

Resets the stored GLONASS almanac

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands