Novatel DL-V3 Reference Manual Download Page 48

Page: 48 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.22.1

Groupuse Translation

groupuse start

•

If position averaging is configured in the group, the

posave

command is executed with averaging

time, maximum horizontal and vertical standard deviation set to the configured values.

groupuse stop

•

If position averaging is configured in the group, this command cancels it and issues a

fix none

command.

Message ID = 63

Table 30: GROUPSAVE Default Configuration

2.23 GROUPSATLIMIT

Limit Number of Satellites for Group

The

groupsatlimit

command allows you to limit the number of satellites used for the group. The

groupsatlimit

set

command sets satlimit for the group named

groupname

satlimit

. The

groupsatlimit

clear

command removes the satlimit setting from the group named

groupname

The

groupsatlimit

default

command sets the satlimit for the group to 0.

Syntax

groupsatlimit

set

groupname

[

satlimit

]

groupsatlimit

default|clear

groupname

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on

Page 41

Enum

none

Group name

Char[]

none

H+4

Maximum time

Double

hours

H+16

Maximum horizontal standard deviation

Double

none

H+24

Maximum vertical standard deviation

Double

none

H+32

Parameter

Power-On

Freset

Stored in NVM

maxtime

no change

0.01

YES

maxhorstd

no change

YES

maxverstd

no change

YES

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands