Novatel DL-V3 Reference Manual Download Page 50

Page: 50 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.24 GROUPSITENAME

Edit Group Site Name

The

groupsitename

command allows you to edit the site name definition for the group.

The

groupsitename

set

command sets the site name for the group named

groupname

sitename

The

groupsitename

clear

and the

groupsitename

default

commands remove the site name setting from

the group named

groupname.

Syntax

groupsitename

set

groupname

sitename

groupsitename

default|clear

groupname

2.24.1

Groupuse Translation

groupuse start

•

The site name is reflected in the

groupdef

log.

•

If an automatic site is being generated (see the

groupmode

command on

Page 46

), the group site

name is used in the site configuration. If the group site name is not specified and an automatic site
is being generated, the log file name is used as the site name.

groupuse stop

•

N/A

Message ID = 59

Table 32: GROUPSITENAME Default Configuration

Field

Data

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on Page 41

Enum

none

Group name

Char[]

none

H+4

Site name

Char[]

none

H+16

Parameter

Power-On

Freset

Stored in NVM

sitename

no change

NUL

YES

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands