Novatel DL-V3 Reference Manual Download Page 51

Page: 51 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

2.25 GROUPSITENUMBER

Edit Group Site Number

The

groupsitenumber

command allows you to edit the site number definition for the group.

The

groupsitenumber

set

command sets the site number for the group named

groupname

sitenumber

The

groupsitenumber

clear

and the

groupsitenumber

default

commands remove the site number

setting from the group named

groupname.

Syntax

groupsitenumber

set

groupname

[

sitenumber

]

groupsitenumber

default|clear

groupname

2.25.1

Groupuse Translation

Syntax

groupuse start

•

The site number setting is reflected in the

groupdef

log.

•

If an automatic site is being generated (see the

groupmode

command on

Page 46

), the group site

number is used in the site configuration.

groupuse stop

•

N/A

Message ID = 61

Table 33: GROUPSITENUMBER Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23

on Page 41

Enum

none

Group name

Char[]

none

H+4

Site number

NUL

Char[]

none

H+16

Parameter

Power-On

Freset

Stored in NVM

sitenumber

no change

NUL

YES

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands