Novatel DL-V3 Reference Manual Download Page 110

Page: 110 / 116

110

DL-V3 Firmware Reference Manual Rev 2

Chapter 4

DL Explorer

Figure 11: Group Management

The

Group Management

dialog displays the current default group table on the PC in the

CDU Groups

panel on the left. The groups stored on the connected receiver are in the

DL Groups

panel on the right.

If the receiver is not connected, or if there are no groups loaded onto the DL-V3, the

DL Groups

panel

is empty.

Up to five groups at a time can be selected for upload from your PC to the receiver. To upload a group,
highlight it in the

CDU Groups

panel.

Select the

UpLoad

button to copy the group.

Select a log group in the

DL Groups

panel and click on the

Start

button to start logging to the CF card.

The

Stop

button becomes active while the DL-V3 is logging the data. Click on the

Stop

button to stop

the DL-V3 from logging the chosen log group. Only one log group may be started at a time.

A red cross beside a log group name indicates the group is not active in the DL-V3. A green check
mark indicates the group is active in the DL-V3.

When there are groups in the

DL Groups

panel, you can also download them to

CDU

. To download

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands