Novatel DL-V3 Reference Manual Download Page 75

Page: 75 / 116

DL-V3 Logs

Chapter 3

DL-V3 Firmware Reference Manual Rev 2

3.1

PDC FILES

In a PDC file, the sequence of data exists in the following format:

Site records’ meteorological logs (MET) may occur at arbitrary locations throughout the file. The
records are linked to allow easy extraction. The file header information block consists of 128 bytes,
see

Table 54.

Table 54: PDC Log Header

The HDRB and GRPB logs are binary versions of the HDRA and GRPA logs described in the
following sections.

Header

FILEHDRB

GPS Logs

SITELOGB #1

GPS Logs

SITELOGB #n

GPS Logs

EOF

Item

Type

Size

Description

Range

Offset

Description

char

File Description. ^Z can be included to
indicate that the description is less than
60 characters.

EOF

byte

C:\ TYPE does not pass this point
(artificial End of File)

Signature

char

“NOVATEL”

FileCode

byte

Indicates the type of file.

Version

byte

Version number

Revision

byte

Revision number

0 to 99

Reserved

byte

Reserved for future use

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands