NorthStar 8000I System Operation Manual Download Page 217

Page: 217 / 220

223

Northstar 8000i Operation Manual

Man Overboard

NOTE: You're recommended to add the following information to your
vessel's man overboard procedure.

When you select the

MOB

button, the 8000i immediately creates a MOB

waypoint at your vessel's current position. This position is also displayed at
the bottom of the

Chart

screen.

As your vessel moves away from the MOB waypoint, the 8000i
automatically draws a line between it and your current position on the

Chart

screen.

The MOB waypoint remains active and cannot be moved.

To de-activate the MOB waypoint:

1. You can either:

select

GoTo

then select

Cancel GoTo Waypoint,

select the MOB waypoint, then select

Cancel GoTo

Waypoint

Summary of Contents for 8000I





























































































































































































































Search results

Summary of Contents for 8000I

Reviews:

Related manuals for 8000I

Brands by name

Popular brands

NorthStar 8000I, System Operation Manual

Search results

Summary of Contents for 8000I

Reviews:

Related manuals for 8000I

Brands by name

Popular brands