manualshive.com logo in svg

NorthStar 8000I, System Operation Manual, Page: 125 / 220

Share
Download
NorthStar 8000I System Operation Manual Download Page 125

 

Northstar 8000i Operation Manual

 

125 

21

 

Use the radar 

This section explains the 

Radar

 screen and status bar, and the radar orientation, 

and explains how to: 

•

 

start the radar transmitting 

•

 

stop the radar transmitting 

•

 

change the range (scale) of the radar display 

•

 

change the radar orientation 

•

 

offset the position of the PPI center 

•

 

set the PPI position to Look Ahead or Center 

•

 

select true or relative motion mode 

•

 

rest the TM position 

If you prefer to see the 

Radar

 screen overlain on your 

Chart 

screen, rather than use 

it as an individual feature, see "Overlay the radar" in the Chart section. The radar 
overlay can help you to quickly identify objects that are not on the chart, such as 
other vessels, and to check that the GPS data is accurate. The heading sensor must 
output data at a 10Hz update rate to ensure accurate synchronization of the chart 
and the radar. 

 

21.1

 

Display the radar screen 

 

To display the radar screen: 

1.  You can either: 

ƒ

 

select 

Display

, then select 

Radar

;  

ƒ

 

select a page that includes the 

Radar

 screen and make this the 

active pane. 

2.  The 8000i displays the 

Radar

 screen, with the 

Radar

 control panel on 

the right hand side of the screen.  

 

21.2

 

Start the radar transmitting 

 

To start the radar transmitting: 

1. Select 

Display

, then select 

Radar

. 

2. The 

Radar Mode

 button shows the current radar mode. Select the 

button to display a drop down list of choices. 

3. Select

 Transmit

. If the radar was: 

ƒ

 

already in 

Standby

 mode, it will start transmitting immediately.  

ƒ

 

Off 

there will be a pause of 90 - 180 seconds while the radar warms 

ups before it starts transmitting.  

4.  The radar will continue transmitting until you change the radar mode 

to Standby or Off. 

 

Summary of Contents for 8000I





























































































































































































































Reviews:

No comments