NorthStar 8000I System Operation Manual Download

Page: 188 / 220

188

Northstar 8000i Operation Manual

3. The

Audio Inpu

t button shows the current source of audio input.

Select the button if you want to change the setting and a drop down
list of choices appears.

4. Select the new setting. The new setting is applied immediately and

stays until you change it again.

5. When you are finished, select

Return

39.4

Play Video Aux In in full screen mode

When you playback the recording, you're recommended to show it only on your
display to get the best quality.

To play the Video Aux In selection in full screen mode:

1. If the Video Aux In selection is already playing and you want it to cover

the entire screen, select

Full Screen

from the control panel.

To show the Video Aux In control panel again:

1. Just touch or click anywhere on the screen, or press any key.

Summary of Contents for 8000I





























































































































































































































Search results

Summary of Contents for 8000I

Reviews:

Related manuals for 8000I

Brands by name

Popular brands

NorthStar 8000I, System Operation Manual

Search results

Summary of Contents for 8000I

Reviews:

Related manuals for 8000I

Brands by name

Popular brands