Home
/
NorthStar
/
8000I
/
System Operation Manual

NorthStar 8000I, System Operation Manual

Share

Page: 108 / 220

NorthStar 8000I System Operation Manual Download Page 108

108

Northstar 8000i Operation Manual

The 200 kHz history in the right hand pane

The 50 kHz history in the left hand pane

5. If you want to adjust the size of the panes, (see "Change the ratio of a

split screen" page 109).

6. When you are finished, select

Return

.

16.13

Select a split zoom screen

You can use a split zoom screen to magnify part of the water column and look at it
in more detail.

It's useful to have the depth line On.

To select a split zoom screen:

1. Display

the

Sounder

screen and the control panel. If you can't see the

Range, Zoom and Split

button, select

Return

.

2. Select

Range, Zoom and Split

. The

View Mode

button shows

the current setting.

3. Select the button if you want to change the setting and a drop down

list of choices appears.

4. Select

Zoom

. The

Sounder

screen changes to show:

The history on the right hand side

The zoomed area of water on the left hand side

The numbers at the top and bottom of the zoomed area show the
upper and lower depths of the zoomed area (see "Change the
zoom range" page 121) if you want to increase or decrease the
extent of the zoomed area)

The number in the center of the zoomed area, and the depth line,
show the center of the zoomed area (see "Change the zoom range
shift" page 108) if you want to move this).

5. When you are finished, select

Return

.

NOTE: If the A-scope is already shown, this will be shown on the split screens too.

16.14

What is zoom range and zoom range shift?

These are available only on a zoomed

Sounder

screen.

The zoom range is the vertical extent of water that is shown in detail on the left
hand side of the split screen; for example, just 5 m of the water column rather than
the complete water column.

Use the zoom range shift to move the zoom range up into shallower water or
down into deeper water, so that you can show any section of the water column in
detail.

16.15

Change the zoom range shift

This works only on a split sounder screen with a zoomed area. You must have Auto
Range Off.

«
...
106
107
108
109
110
...
»

Summary of Contents for 8000I





























































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands