manualshive.com logo in svg

NorthStar 8000I, System Operation Manual

Share
Download
NorthStar 8000I System Operation Manual Download Page 118

 

118

 

Northstar 8000i Operation Manual

18.7

 

Change the range shift 

 

To adjust the range shift: 

1. Display 

the 

Sounder

 screen and the control panel. If you can't see the 

Range, Zoom and Split

 button, select 

Return

. 

2. Select 

Range, Zoom and Split

.  

3. The 

Range Shift

 button shows the current setting. Select the 

button if you want to change the setting.  

4.  The current range shift is shown in the control panel. Select: 

ƒ

 

Shallower

 to view a different part of the water column, closer to 

the surface 

ƒ

 

Deeper

 to view a different part of the water column, closer to the 

bottom  

5.  The new setting is applied immediately and stays until you change it 

again. Select 

OK

 to confirm the new setting.  

NOTE: If you select Vessel, the upper value of the range shift resets to 0  
automatically.  

 

18.8

 

Change the range 

Range is the vertical extent shown on the 

Sounder

 screen. You can increase or 

decrease the range. 

 

To change the range: 

1. Display 

the 

Sounder

 screen and the control panel. If you can't see the 

Range, Zoom and Split

 button, select 

Return

. 

2. Select 

Range, Zoom and Split

. The depth column shows the 

current range. Use the keys on the remote keypad or on your display 
processor to select: 

ƒ

 

Out

 if you want to increase the range 

ƒ

 

In 

if you want to decrease the range 

3.  The new setting is applied immediately and stays until you change it 

again. 

 

Summary of Contents for 8000I





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands