manualshive.com logo in svg

NorthStar 8000I, System Operation Manual

Share
Download
NorthStar 8000I System Operation Manual Download Page 90

 

90

 

Northstar 8000i Operation Manual

4. The 

Look Ahead Distance

 button shows the current setting. 

Select 

EDIT

 if want to change the setting, then use the onscreen 

keyboard to enter the new setting and select 

OK

. You don't need to 

enter the % symbol.  

5.  The new setting is applied immediately and stays until you change it 

again. 

6.  When you are finished, select 

– Navigation.

 

 

12.6

 

Set the center circle to update chart 

If you've selected the vessel offset to be center mode, you can use the center circle 
setting to make the 

Chart

 screen (and the 

Radar

 screen) reposition after your 

vessel has travelled a certain distance across it, so that you can keep a good view 
of what lies ahead.  

The distance is expressed as a percentage. For example, if you set the center circle 
distance to 50%, the 

Chart

 screen will reposition automatically when your vessel is 

halfway between the center and the edge of the 

Chart

 screen.  

20% is the default.  

 

To change the center circle setting: 

1. Select 

Display

. 

2. Select

 Setup

 from the control panel. 

3. Select 

+ Navigation

 to show a list of navigation specification 

options. 

4. The 

Center Circle to Update Chart

 button shows the current 

setting. Select 

EDIT

 if want to change the setting, then use the 

onscreen keyboard to enter the new setting and select 

OK

. You don't 

need to enter the % symbol.  

5.  The new setting is applied immediately and stays until you change it 

again. 

6.  When you are finished, select 

– Navigation.

 

 

12.7

 

Set the amount of time represented by the course 
predictor line 

You can use the course predictor line to estimate where your vessel will be in a 
specified number of minutes, if you maintain your current COG and SOG.  

The course predictor line is drawn on your 

Chart

 screen and extends out from your 

vessel in the direction of your COG. Each minute is marked by a solid circle on the 
course predictor line. 

Ten minutes is the default.  

 

To change the time period for the course predictor line: 

1. Select 

Display

. 

2. Select

 Setup

 from the control panel. 

Summary of Contents for 8000I





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands