NorthStar 8000I System Operation Manual Download Page 148

Page: 148 / 220

148

Northstar 8000i Operation Manual

Set up the radar

The following settings are specified as part of the installation, but you can change
them at any time, if necessary:

•

radar startup mode

•

antenna (scanner) height

•

parking angle (for an open array)

•

range of the radar

•

radar bearing alignment

27.1

Change the radar startup mode

To change the radar startup mode:

1. Select

Display

2. Select

Setup

from the control panel.

3. Select

Radar

to show a list of radar specification options.

4. Select

Radar Power on Action

, then select:

Standby

if you want the scanner to warm up and then remain in

Standby mode when the 8000i starts up. This is the default. The
warm up can take 90 - 180 seconds, and an open array will rotate to
face the bow.

Remain Off

if you want the scanner to remain Off when the 8000i

starts up. This saves on power consumption and magnetron usage.

5. When you are finished, select

– Radar

27.2

Change the radar antenna height

It is important to correctly specify the height of the antenna (scanner) above the
waterline so that the sea clutter control works properly.

To change the radar antenna height:

1. Select

Display

2. Select

Setup

from the control panel.

3. Select

Radar

to show a list of radar specification options.

4. Select

EDIT

next to the

Radar Antenna Height

option, then

use the online keyboard to enter the height of the radar scanner above
sea level. Select

to confirm the new setting.

5. When you are finished, select

– Radar

27.3

Change the parking angle

When an open array radar is turned Off, it continues to rotate for a while before it
finally stops. The stop position is known as the parking angle. You can adjust the
parking angle so that the open array will stop at your preferred position.

Summary of Contents for 8000I





























































































































































































































Search results

Summary of Contents for 8000I

Reviews:

Related manuals for 8000I

Brands by name

Popular brands

NorthStar 8000I, System Operation Manual

Search results

Summary of Contents for 8000I

Reviews:

Related manuals for 8000I

Brands by name

Popular brands