NorthStar 8000I System Operation Manual Download Page 196

Page: 196 / 220

196

Northstar 8000i Operation Manual

42.16

Restore routes, tracks, and waypoints

Use this to restore your routes, tracks, and waypoints if the data has been
corrupted.

To restore your routes, tracks, and waypoints:

1. Select

Display

2. Select

Setup

from the control panel.

3. Select

+ Restore

to display a list of system options.

4. Select

Routes Tracks and Waypoints

5. The 8000i displays the Restore Routes, Tracks and Waypoints to Master

box with a list of the backups for all the display units in the 8000i
networked system.

6. Select

either:

the backup that you want to restore, then select

Restore

Selected Backup

, then select

to confirm.

Restore Factory Defaults

to restore the local settings to the

factory defaults, then select

to confirm.

7. Select

again.

8. When you are finished, select

Return

, then select

– Restore

42.17

Restore global settings

Use this to restore the global settings if the data has been corrupted.

Global settings are applied to all the display units in the 8000i networked system.
The global settings are stored on the master unit.

To restore your global settings:

1. Select

Display

2. Select

Setup

from the control panel.

3. Select

+ Restore

to display a list of system options.

4. Select

Restore Global Settings

5. The 8000i displays the Restore Global Settings to Master box with a list

of the backups for all the display units in the 8000i networked system.

6. Select

either:

the backup that you want to restore, then select

Restore

Selected Backup

, then select

to confirm.

Restore Factory Defaults

to restore the local settings to the

factory defaults, then select

to confirm.

7. Select

again.

8. When you are finished, select

Return

, then select

– Restore

Summary of Contents for 8000I





























































































































































































































Search results

Summary of Contents for 8000I

Reviews:

Related manuals for 8000I

Brands by name

Popular brands

NorthStar 8000I, System Operation Manual

Search results

Summary of Contents for 8000I

Reviews:

Related manuals for 8000I

Brands by name

Popular brands