manualshive.com logo in svg

NorthStar 8000I, System Operation Manual

The NorthStar 8000I Installation Manual is available for free download on our website. This comprehensive user manual provides step-by-step instructions and guidelines for installing this cutting-edge product. Obtain this manual now from manualshive.com, ensuring a seamless and hassle-free installation process for the NorthStar 8000I.

Share
Download
background image

 

Northstar 8000i Operation Manual

 

11 

 

19

 

Set up the sounder 

119

 

19.1

 

Change the transducer depth ..........................................................................................................119

 

19.2

 

Change the water temperature offset...........................................................................................120

 

19.3

 

Change the water temperature averaging time ........................................................................120

 

19.4

 

Change the sounder's speed offset................................................................................................120

 

19.5

 

Change the sounder's speed filter ..................................................................................................121

 

19.6

 

Change the zoom range.....................................................................................................................121

 

20

 

Radar 123

 

20.1

 

How the radar works ...........................................................................................................................123

 

20.2

 

What are the radar modes? ...............................................................................................................123

 

21

 

Use the radar 

125

 

21.1

 

Display the radar screen.....................................................................................................................125

 

21.2

 

Start the radar transmitting ..............................................................................................................125

 

21.3

 

Stop the radar transmitting ..............................................................................................................126

 

21.4

 

What does the radar screen show?.................................................................................................126

 

21.5

 

What does the radar status bar show? ..........................................................................................127

 

21.6

 

What is the radar orientation?..........................................................................................................127

 

21.7

 

Change the radar orientation...........................................................................................................128

 

21.8

 

Change the radar range offset .........................................................................................................128

 

21.9

 

Customize the position of the PPI center.....................................................................................128

 

21.10

 

Set the PPI position to Look Ahead or Center.............................................................................129

 

21.11

 

Select True or Relative Motion mode ............................................................................................129

 

21.12

 

Reset the TM position .........................................................................................................................130

 

22

 

Optimize the quality of the radar display 

131

 

22.1

 

Change the radar gain mode............................................................................................................131

 

22.2

 

Change the radar gain setting .........................................................................................................132

 

22.3

 

What is sea clutter? ..............................................................................................................................132

 

22.4

 

Change the sea clutter mode ...........................................................................................................132

 

22.5

 

Change the sea clutter setting.........................................................................................................133

 

22.6

 

What is rain clutter? .............................................................................................................................133

 

22.7

 

Change the rain setting......................................................................................................................134

 

22.8

 

Reduce interference from other radars.........................................................................................134

 

23

 

Customize the radar screen 

136

 

23.1

 

Change the radar palette...................................................................................................................136

 

23.2

 

Show/hide the North indicator........................................................................................................136

 

23.3

 

Show/hide the heading marker.......................................................................................................137

 

23.4

 

Show/hide the range rings................................................................................................................137

 

23.5

 

Show/hide the active waypoint on radar .....................................................................................137

 

23.6

 

Show/hide the active route on radar.............................................................................................138

 

23.7

 

Show/hide waypoint or route details on radar ..........................................................................138

 

Summary of Contents for 8000I





























































































































































































































Reviews:

No comments

Related manuals for 8000I

Qstarz eXtreme BT-Q818XT Quick Installation Manual preview
eXtreme BT-Q818XT
Brand: Qstarz Pages: 6
Qstarz BT-Q1300S Quick Installation Manual preview
BT-Q1300S
Brand: Qstarz Pages: 101
Globalsat GTR-388A12 Quick Start Manual preview
GTR-388A12
Brand: Globalsat Pages: 17
Navitel RE 5 DUAL User Manual preview
RE 5 DUAL
Brand: Navitel Pages: 217
Navilock NL-125O User Manual preview
NL-125O
Brand: Navilock Pages: 36
UniGuard GT06R User Manual preview
GT06R
Brand: UniGuard Pages: 6
RedPort XTRACKER IR Quick Start Manual preview
XTRACKER IR
Brand: RedPort Pages: 4
Cantrack G200 Manual preview
G200
Brand: Cantrack Pages: 6
SCRAM Systems GPS-600 Quick Reference Manual preview
GPS-600
Brand: SCRAM Systems Pages: 40
O-Synce NAVI2move User Manual preview
NAVI2move
Brand: O-Synce Pages: 16
Javad BTCONF User Manual preview
BTCONF
Brand: Javad Pages: 26
Becker Highspeed 7934 Specifications preview
Highspeed 7934
Brand: Becker Pages: 2
Enfora MT4100 Installation Manual preview
MT4100
Brand: Enfora Pages: 6
Klarfit 10026910 Manual preview
10026910
Brand: Klarfit Pages: 12
uAvionix tailBeacon STC Instructions For Continued Airworthiness And Maintenance Manual preview
tailBeacon STC
Brand: uAvionix Pages: 19
Satguide BT? GPS?8 User Manual preview
BT? GPS?8
Brand: Satguide Pages: 19
Polyend Tracker Instructions Of Use preview
Tracker
Brand: Polyend Pages: 47
YOYOMOTION YOYOCare P3 User Manual Supplement preview
YOYOCare P3
Brand: YOYOMOTION Pages: 2

Brands by name

Popular brands

Load more brands