Nikon Total Station DTM-322 Instruction Manual Download Page 6 | Manualshive

Page: 6 / 185

background image

vi

Total Station DTM-322 Instruction Manual

C

WARNING –

Before storing the battery or battery charger, cover the contact points with

insulation tape. If you do not cover the contact points, the battery or charger may short circuit,
causing fire, burns, or damage to the instrument.

C

WARNING –

The battery is not itself waterproof. Do not get the battery wet when it is removed

from the instrument. If water seeps into the battery, it may cause a fire or burns.

Cautions

Before using the instrument, read the following cautions and follow the instructions
that they provide:

C

CAUTION –

Do not use controls or adjustments, or carry out any procedures, other than those

specified in this document. Otherwise you may be exposed to hazardous radiation.

C

CAUTION –

The tops of the tripod ferrules are very sharp. When handling or carrying the

tripod, take care to avoid injuring yourself on the ferrules.

C

CAUTION –

Before carrying the tripod or the instrument in the carrying case, check the

shoulder strap and its clasp. If the strap is damaged or the clasp is not securely fastened, the
carrying case may fall, causing personal injury or instrument damage.

C

CAUTION –

Before setting up the tripod, make sure that no-one’s hands or feet are underneath

it. When the legs of the tripod are being driven into the ground, they could pierce hands or feet.

C

CAUTION –

After mounting the instrument on the tripod, securely fasten the thumb screws on

the tripod legs. If the thumb screws are not securely fastened, the tripod may collapse, causing
personal injury or instrument damage.

C

CAUTION –

After mounting the instrument on the tripod, securely fasten the clamp screw on

the tripod. If the clamp screw is not securely fastened, the instrument may fall off the tripod,
causing personal injury or instrument damage.

C

CAUTION –

Securely fasten the leveling base clamp knob. If the knob is not securely fastened,

the leveling base may come loose or fall off when you lift the instrument, causing personal
injury or instrument damage.

C

CAUTION –

Do not stack objects on the plastic carrying case, or use it as a stool. The plastic

carrying case is unstable and its surface is slippery. Stacking or sitting on the plastic carrying
case may cause personal injury or instrument damage.

«
...
4
5
6
7
8
...
»

Summary of Contents for Total Station DTM-322


























































































































































































Reviews:

No comments

Related manuals for Total Station DTM-322

Brand: Kawai Pages: 142

Brand: Kawai Pages: 10

Brand: C-LOGIC Pages: 4

Brand: Olympus Pages: 12

Brand: Teledyne Hastings Instruments Pages: 54

Brand: Hanna Instruments Pages: 9

DUSTHUNTER C200

Brand: SICK Pages: 126

FlowStar2 LB 514

Brand: BERTHOLD TECHNOLOGIES Pages: 130

Brand: Megger Pages: 8

Brand: NARDA Pages: 14

Brand: Hanna Instruments Pages: 2

Brand: GARO Pages: 15

Brand: Mountz Pages: 27

Brand: Bullhorn Pages: 44

Brand: Spirax Sarco Pages: 64

Brand: Metrohm Pages: 163

Brand: Jula Pages: 17

Brand: Level Pro Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands