Nikon Total Station DTM-322 Instruction Manual Download Page 84

Page: 84 / 185

Applications

Total Station DTM-322 Instruction Manual

If the curve length (Len) is too large for a circle of the
given radius, it is shortened.

Using

[DSP]

to switch between display screens

Press

[DSP]

to switch between the Stakeout display screens. The following screens are

available:

The ARC5 screen is only available if the secondary distance unit is set. For more
information, see

Others settings, page 109

Every time you press

[DSP]

, the next screen appears. If you press

[DSP]

in the last screen

(ARC4 or ARC5), the ARC1 screen appears.

To record the point, press

[ENT]

on any observation

screen. The arc is stored in comment records.

Sample records

CO,Arc P1:583 AZ1=0.0000 P2:102
CO, AZ2=311.2932 Radius=50.0000 Length=125.6637
CO, Sta= -12.6876 Offset= 1.3721 dZ= 0.0971
SS,17,1.0000,6.9202,18.4700,80.3120,15:48:48,2REF-LINE

To ...

Press ...

switch between display screens

[DSP]

change HT

[HOT]

record points

[ENT]

ARC1

ARC2

ARC3

ARC4

Sta
O/S

X
Y
Z

HA
VA
SD

HA
VD
HD

ARC5

HD
VD
SD

Summary of Contents for Total Station DTM-322


























































































































































































Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands

Nikon Total Station DTM-322, Instruction Manual

Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands