Nikon Total Station DTM-322 Instruction Manual Download Page 171

Page: 171 / 185

Total Station DTM-322 Instruction Manual

157

Communications

Coordinates record

Observation record

08KI

pt northing

easting

elevation

desc

1–4

08KI

Coordinates record identifier (fixed text)

5–8 (2x),
5–20 (33)

Point number

9–18 (2x),
21–36 (33)

northing

Northing of the coordinate

19–28 (2x),
37–52 (33)

easting

Easting of the coordinate

29–38 (2x),
53–68 (33)

elevation

Elevation of the coordinate

39–54 (2x),
69–84 (33)

desc

Feature code

09MC

stnpt

pt sd va ha desc

1–4

09MC

Observation record identifier (fixed text)

5–8 (2x),
5–20 (33)

stnpt

Station point number

9–12 (2x),
21–36 (33)

Observed point number

13–22 (2x),
37–52 (33)

Slope distance

23–32 (2x),
53–68 (33)

Vertical angle

33–42 (2x),
69–84 (33)

Horizontal angle

43–58 (2x),
85–100 (33)

desc

Feature code

Summary of Contents for Total Station DTM-322


























































































































































































Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands

Nikon Total Station DTM-322, Instruction Manual

Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands