Nikon Total Station DTM-322 Instruction Manual Download Page 138

Page: 138 / 185

Menu Key

124

Total Station DTM-322 Instruction Manual

Adding a layer

In the point or code list, press the

Layer

softkey.

Enter the name of the new layer.

To change between alphabetic and numeric input
mode, press

[MODE]

. To store the new layer, press

[ENT]

The new layer is added to the list in alphabetic
order.

Communication

Use the Communication menu to download or upload
data. To display the Communication menu, press

[5]

select

Comm.

on the MENU screen.

Downloading data

To go to the download settings screen, press

[1]

or select

Download

in the Communication menu.

To display the total number of records that will be
downloaded, press [ENT] in the Data field.

Format

NIKON
SDR2x
SDR33

Data

RAW
Coordinate

Summary of Contents for Total Station DTM-322


























































































































































































Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands

Nikon Total Station DTM-322, Instruction Manual

Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands