Nikon Total Station DTM-322 Instruction Manual Download Page 81

Page: 81 / 185

Total Station DTM-322 Instruction Manual

Applications

Using

[DSP]

to switch between display screens

You can use

[DSP]

to switch between display screens. This function works as in the

angle-distance stakeout. For more information, see

Using [DSP] to switch between

display screens, page 62

Program Key

To display the Programs menu, press

[PRG]

Measuring distance and offset values along a specified line

Press

[1]

or select

2Pt RefLine

in the

Programs menu.

Enter the first point for the reference line.
Alternatively (to enter the point by measuring),
press the

MsrPT

softkey.

Enter the second point for the reference line.

Enter an asterisk (*) in the PT field to perform a
wildcard search. A list of matching points
appears. Highlight a point in the list and then
press

[ENT]

Direct Measurement screen

Press the

MsrPT

softkey to display a direct measurement screen.

Sight the target and press

[MSR1]

[MSR2]

. The Record PT screen appears.

If you press

[ESC]

in the Record PT screen, the measured point is used but

not recorded in the job.

Summary of Contents for Total Station DTM-322


























































































































































































Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands

Nikon Total Station DTM-322, Instruction Manual

Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands