Nikon Total Station DTM-322 Instruction Manual Download Page 30

Page: 30 / 185

Preparation

Total Station DTM-322 Instruction Manual

Setting Up the Prism Reflector

Assemble the prism reflector as shown below.

Adjust the height of the tribrach adaptor (see

page 16

If necessary, change the direction of the prism (see

page 17

Set the prism constant (see

page 17

If you are using a single prism holder, set the position of the target plate (see

page 17

Detailed instructions for Step 2 through Step 5 are provided on the following pages.

Adjusting the height of the tribrach adapter

The tribrach adapter has two height settings. To use the prism reflector with a DTM-
322 instrument, use the lower height setting.

To adjust the height of the tribrach adapter:

Remove the height adjustment screw from
the tribrach adapter.

Slide the tribrach adapter up or down the
prism holder mount until the height
adjustment screw holes on the prism holder
mount and on the tribrach adapter are
aligned.

Replace and tighten the adjustment screw.

Tribrach adapter 13/14

Tribrach

Tripod

Target plate for single prism

Tiltable single

prism holder

Prism C

Target pole

Triple prism holder

Prism holder mount

Height adjustment

screw

Summary of Contents for Total Station DTM-322


























































































































































































Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands

Nikon Total Station DTM-322, Instruction Manual

Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands