Nikon Total Station DTM-322 Instruction Manual Download Page 40

Page: 40 / 185

Getting Started

Total Station DTM-322 Instruction Manual

Status bar

The status bar appears on the right side of every
screen. It contains icons that indicate the status of
various system functions.

Signal indicator

The signal indicator shows the reflected light intensity:

Input mode indicator

The Input mode indicator only appears when you are entering points or coordinates. It
shows the data input mode:

Battery indicator

The battery indicator shows the battery voltage level:

Level 4 (maximum)

Level 3

Level 2

Level 1 (minimum)

If this icon is blinking, the signal is flickering.

If this icon is blinking rapidly, the signal is low.
If this icon is blinking slowly, there is no signal.

If there is no icon, analog power for EDM is off.

Input mode is numeric. Press a key on the number pad to enter the number printed on
the key.

Input mode is alphabetic. Press a key on the number pad to enter the first letter printed
beside the key. Press the key repeatedly to cycle through all the letters assigned to that
key.
For example, to enter the letter O in alphabetic mode, press

[5]

three times.

Level 4 (Full)

Level 3

Level 2

Level 1

Battery low

Status bar

Summary of Contents for Total Station DTM-322


























































































































































































Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands

Nikon Total Station DTM-322, Instruction Manual

Search results

Summary of Contents for Total Station DTM-322

Reviews:

Related manuals for Total Station DTM-322

Brands by name

Popular brands