manualshive.com logo in svg

Nikon Total Station DTM-322, Instruction Manual, Page: 123 / 185

Share
Download
Nikon Total Station DTM-322 Instruction Manual Download Page 123

Total Station DTM-322 Instruction Manual     

109

Menu Key     

5

Others settings

To open the Others menu, press 

[9]

 or select 

Other

 in 

the Settings menu. 

B

Tip – 

To provide easier configuration for common regional settings, you can quickly configure 

the Nikon total station to a pre-set combination of default regional settings. For more 
information, see 

Changing Regional Configuration Pre-sets, page 22

.

B

Tip – 

The Nikon total station supports up to 3 languages on the instrument. For more 

information on changing the language settings, see 

page 21

.

XYZ disp

Fast/Norm/Slow/+ENT
Defines speed to move to the next screen after 
showing XYZ of the input PT

2nd Unit

None/Meter/US-Ft/I-Ft

When the Secondary unit is set to a unit, an 
extra display screen is available in the BMS, 
stakeout observation screens, and 2-pt 
reference line screens. The extra screen shows 
the HD, VD, and SD in the secondary unit.

If you select US-Ft or I-Ft, an additional settings screen appears. Use this 
screen to specify whether to display values in Decimal-Ft or Ft-Inch.

Sig Beep

ON/OFF

Split ST

No/Yes
Select Yes to separate the point numbers of 
station points from other record type point 
numbers

If you set the Split ST field to Yes, an additional setting screen appears. Use 
this screen to specify the starting ST number.

CD Input

ABC/123
Sets the default input mode when a CD field 
appears.

Owner’s Detail Up to 20 characters.

Enter your name or the name of your 
company. If you enter a value in this field, it 
appears at start-up.

Summary of Contents for Total Station DTM-322


























































































































































































Reviews:

No comments