314
Len
s measu
ring error
(ERROR
2**)
201
LMU feeler off error
• Use a lens with a larger diameter
• Change the layout.
• If the error occurs when the feeler is not off, calibrate
the lens measuring ASSY or check the wear of the
feeler and replace it if necessary.
202
LMU lens detection error
• Set a lens.
• Replace the feeler.
• Calibrate the lens measuring ASSY.
203
LMU lens thickness error
• Calibrate the lens measuring ASSY.
• Replace the feeler.
204
LMU start and end points error
• Replace the unit of the lens measuring ASSY. (The
guide rail for the feeler vertical movement is defective.
Replace the guide rail.)
• Clean the lens measuring window.
• Check for any foreign matter on the lens.
• Adjust the measurement position.
205
LMU origin sensor error
• Check whether processing waste is adhered to the
lens measuring window.
• Check the forward/backward movement of the lens
measuring ASSY.
• Check whether anything is snagging on or interfering
with the cable.
• Check the cable connection. Check for cable
breakage.
206
LMU rear feeler origin sensor error • Check whether anything is interfering with the feeler arm.
• Replace the origin sensor.
• Check the cable connection. Check for cable
breakage.
• Check for any looseness in the cam.
207
LMU front feeler origin sensor error
208
LMU operation end error
• Check whether anything is interfering with the feeler
arm.
• Check whether the forward/backward movement of
the LMU is smooth.
• Check whether the feelers contact a lens when the
LMU comes out.
• Check the operation of motor driver MD08.
• Replace motor driver MD08.
209
LMU feeler close error
• Check whether anything is interfering with the feelers.
• Check the vertical movement of the feelers.
• Check whether the lens is too thick.
210
LMU feeler origin sensor off error
• Check whether anything is interfering with the feelers.
• Check for any looseness on the cam.
214
LMU rear feeler encoder error
• Check for cable breakage or poor connection of the
rear side feeler encoder.
• Replace the rear side feeler encoder.
215
LMU front feeler encoder error
• Check for cable breakage or poor connection of the
front side feeler encoder.
• Replace the front side feeler encoder.
Dat
a error
(E
R
R
OR 3*
*)
301
Calculation error
• Process a lens in passive mode.
• Check the shape.
302
EEPROM checksum error
• Check whether the data such as adjustment values
has any abnorality after writing the checksum.
• Replace BA01.
304
EEPROM data error
• Initialize the EEPROM and readjust it.
Type
Error code
Message
Remedy
Summary of Contents for SE-9090 Supra
