© 2020 Copyright Newmar Corporation. All rights reserved. For the most up-to-date version of this content, and for more product-specific information, please refer to Newgle.
86
ELECTRICAL
TIME/DATE SCREEN
View and/or set the current time and date on the ATS. To
get to the TIME/DATE screen from the main screen, push
the front lever right or left repeatedly until you see the time
and date. To set, press the lever IN once quickly. You will
see a blinking cursor. Push the lever left until the cursor is
over the minutes digit.(Do not try to set the seconds - they
reset to zero.) Once you have the correct setting for the
minutes, continue on with setting the hour, date, month,
year and so on by pushing the lever to the left.
Once you have entered the correct time and date, press
and HOLD the lever IN for 3 seconds. You will see “TIME IS
SET” once complete. You can now release the lever.
When you are on the TIME DATE screen and the cursor
is not blinking, you can navigate to the other top level
screens such as the main screen, or the L1 volts screen, etc.
VIEW FAULTS SCREEN
This allows you to view the faults recorded whenever
the ATS detected a fault with electrical power. To view,
momentarily push the front lever DOWN or IN. The
screen will display fault 1, which is the most recent fault
that occurred and was detected by the ATS. The screen
will scroll through the following items for fault 1 every 3
seconds:
1.
MODE- State of ATS when fault occurred (MODE
SHORE = shore power; MODETGEN = transferring to
Gen power, etc.)
2.
FAULT CODE (L1 LO, L2 LO, etc.)
3.
L1/L2 Volts and Currents at the time of the fault.
4.
Frequency of Line 2
5.
Time of Fault
6.
Date of Fault
Operating Instructions
SCREEN NAVIGATION USING THE
BUTTON/LEVER
There are several information screens associated with the
Remote Display which can be selected via the lever on the
front of the unit. Pushing the lever to the RIGHT repeatedly
will access the screens in the following order. Pushing
the lever to the LEFT accesses the screens in the reverse
order.
When the VIEW FAULTS screen is displayed, momentarily
pushing the lever in accesses a log of faults which have
been stored by the ATS unit. Viewing the fault log data will
be explained in more detail below.
DISPLAY FOR NORMAL OPERATION
During normal operation, the Remote Display screen reads
the status of the RV electrical power, showing continuous
voltages and currents for power lines 1 and 2 coming into
the RV on the main screen. A secondary screen showing
SHORE or GEN will momentarily display approximately
every 8 seconds, indicating whether your RV is running on
power for your shore connection or whether the ATS has
transferred you over to generator power.
DISPLAY DURING FAULT CONDITIONS
If there are any faults or problems with your electrical
power, the Remote Display will show the particular faults
on the LCD screen with a 3 second interval between each
item. The faults displayed can be any combination of the
ATS fault codes.
DISPLAY DURING DELAY STATE
When the ATS is powered up, the Remote Display will
display “Delay” and the elapsed time in seconds until it
reaches 128 seconds. After the delay is completed, if shore
power is good the ATS will connect power to the RV, and
the unit will go to the normal operating screen showing
voltages and currents as described above.
L1 VOLT | L2 VOLT SCREENS
These screens are useful for viewing the line voltages
when the main screen is in delay or when L1 or L2 have
a fault (line voltage that is too low or too high). The main
screen will display line voltage between 102 and 132 volts;
otherwise it will show that the line has a fault. The L1 VOLT
and L2 VOLT screens however display a greater range,
from 90 to 140 Volts. The L2 VOLT screen is only shown
when using a 50 Amp ATS.
L1 CURR | L2 CURR
These screens are useful for viewing the line currents in
amps when the Main Screen is in Delay or when it shows
that L1 or L2 have a fault. The L2 CURR screen is only
shown when using a 50 Amp ATS.
Summary of Contents for Canyon Star 2021
Page 1: ...2021 sm ...
