manualshive.com logo in svg

NETGEAR GSM7352S - ProSafe Switch - Stackable, User Manual

The NETGEAR GSM7352S ProSafe Switch is a versatile and stackable network switch designed for seamless connectivity. Enhance your network with this high-performance device. To maximize your experience, don't forget to download the free User Manual from manualshive.com to unlock its full potential.

Share
Download
background image

  Chapter 4.  Routing

 

   

|

     

229

ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 

Secondary IP Address

To display the Secondary IP Address page, click 

Routing

 IP

 Advanced 

 Secondary IP

.

1. 

Use 

Interface

 to select the interface for which data is to be displayed or configured.

2. 

Use 

Secondary IP Address

 to add a secondary IP address to the selected interface.

3. 

Use 

Secondary IP Subnet Mask

 to enter the subnet mask for the interface. This is also 

referred to as the subnet/network mask, and defines the portion of the interface's IP Address 
that is used to identify the attached network. This value is read only once configured.

4. 

Click 

ADD

 to add a Secondary IP Address for the selected interface.

5. 

Click 

DELETE

 to delete the Secondary IP Address from the selected interface.

Table 12.  

Field

Description

VLAN ID

The VLAN ID associated with the displayed or 
configured interface.

Primary IP Address

The Primary IP Address for the Interface.

IPv6

IPv6 is the next generation of the Internet Protocol. With 128-bit addresses, versus 32-bit 
addresses for IPv4, IPv6 solves the address depletion issues seen with IPv4 and removes 
the requirement for Network Address Translation (NAT), which is used in IPv4 networks to 
reduce the number of globally unique IP addresses required for a given network. Its 
aggregate addresses can dramatically reduce the size of the global routing table through well 
known address combinations. Security is more integrated and network configuration is 
simplified yet more flexible.

IPv6 can coexists with IPv4. As with IPv4, IPv6 routing can be enabled on physical and VLAN 
interfaces. Each L3 routing interface can be used for IPv4, IPv6, or both. IP protocols running 
over L3 (for example, UDP and TCP) do not change with IPv6. For this reason, a single CPU 
stack is used for transport of both IPv4 and IPv6, and a single sockets interface provides 

Summary of Contents for GSM7352S - ProSafe Switch - Stackable





















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GSM7352S - ProSafe Switch - Stackable

NEC 2400 Integration Manual preview
2400
Brand: NEC Pages: 168
A SYSTEMS AV50 User Manual preview
AV50
Brand: A SYSTEMS Pages: 16
B&K HD6 Product Manual preview
HD6
Brand: B&K Pages: 2
B&B Electronics 232BSS4 Manual preview
232BSS4
Brand: B&B Electronics Pages: 45
H3C S5560S-EI Series Troubleshooting Manual preview
S5560S-EI Series
Brand: H3C Pages: 37
3Com OfficeConnect WX4400 Reference Manual preview
OfficeConnect WX4400
Brand: 3Com Pages: 528
GALCO EX95000 Series Quick Start Manual preview
EX95000 Series
Brand: GALCO Pages: 22
IDEM SAFETY SWITCHES KLM-P2L Operating Instructions preview
KLM-P2L
Brand: IDEM SAFETY SWITCHES Pages: 2
Hirschmann PAT TRS 05 / PATB3 Installation And Setup Manual preview
PAT TRS 05 / PATB3
Brand: Hirschmann Pages: 12
SMART Hub VE220 Installation And User Manual preview
Hub VE220
Brand: SMART Pages: 46
Ubiquiti EdgeSwitch 10 XP Quick Start Manual preview
EdgeSwitch 10 XP
Brand: Ubiquiti Pages: 13
Campbell HUB-SDM5 Instruction Manual preview
HUB-SDM5
Brand: Campbell Pages: 10
V7 MPEGS24 User Manual preview
MPEGS24
Brand: V7 Pages: 35
Eaton RMQ-Titan M22-LED Series Instruction Leaflet preview
RMQ-Titan M22-LED Series
Brand: Eaton Pages: 4
Microsens MS650850M Application preview
MS650850M
Brand: Microsens Pages: 8
Maipu S12800 Installation Manual preview
S12800
Brand: Maipu Pages: 135
Black Box Personal MiniHub Manual preview
Personal MiniHub
Brand: Black Box Pages: 22
PIKA mWARP Manual preview
mWARP
Brand: PIKA Pages: 7

Brands by name

Popular brands

Load more brands