NeoDen NeoDen10 User Manual Download Page 62 | Manualshive

Page: 62 / 64

background image

62

6

Set pre-welding detection station (manual or AOI)

In sum, P&P machine's running speed and placement accuracy still has limit. Peoples work is important to run machine on
its proper role. So, it’s necessary to comply with effective measures to keep machine normal work, its placement quality and
efficiency.

14.2 Maintenance

Arrange regular inspection and maintenance system.

14.2.1 Daily Inspection

Items

Items check before
power on

①

Temperature& Moisture: Temperature 20

℃

～

26

℃

, humidity 45~70%

②

Indoor environment: Air clean without aggregate air.

③

No clutters within the placement area and keep rails clean.

④

No spots on cameras and keep lens clean.

⑤

No obstacles around the head nozzles

⑥

Checking if nozzles are dirty, distorted; If so, please clean or change the

nozzle.

⑦

Checking if feeders are correctly installed in stacks and confirm no clutters

on stack.

⑧

Checking the connection of air connector and air hose

⑨

Checking air pressure.

Items check after
power on

①

Checking if the monitor display normally after system start up.

②

Checking if emergency button can work normally or not.

③

Checking if placement head can move back to the origin.

④

Checking if there’s abnormal noise while placement head move.

⑤

Checking all nozzles vacuum pressure.

⑥

Checking if PCB moving on rails smoothly or not; Sensor workable or not.

⑦

Checking if the board has been well fixed by magnetic bar and pins.

14.2.2 Monthly Inspection

Items

Detailed Inspection

X/Y axis

Make sure no abnormal noise while placement head moving.

X/Y motor

Make sure X/Y motors no overheating.

Nozzle

Checking if all nozzles are good without bend and nozzle surface is horizontal

Air hose

Checking the connection between air hose and machine, keep sure the hose in good
situation without wearing or air leaking.

Step motor

Checking if any dirty on step motor, synchronous belt, Synchronous wheel. Make sure the
Z-axis motor can up, down and rotate smoothly.

Z-axis motor

Checking if the placement head can go up and down smoothly. Use your finger to push the

«
...
60
61
62
63
64
»

Summary of Contents for NeoDen10

































































Reviews:

No comments

Related manuals for NeoDen10

Brand: Hagie Pages: 61

Brand: JackJaw Pages: 2

DISHSTAR ADA-SEER

Brand: Jackson Pages: 2

Brand: Rainin Instrument Pages: 16

FUSION APOLLO MS-WB675

Brand: Garmin Pages: 18

Brand: Rapid Shape Pages: 12

MultiFill 003-561-005

Brand: Hanskamp Pages: 20

Brand: Megger Pages: 12

Brand: Tecsis Pages: 52

Brand: Airway Pages: 2

Brand: Crazy Foil Pages: 8

Brand: Petromax Pages: 16

HomeFill HF2POST6

Brand: Invacare Pages: 24

Brand: WhizRider Pages: 24

Brand: NTN Pages: 19

Brand: Baileigh Pages: 39

ArcticPro 200yf

Brand: MAHLE Pages: 2

Brand: W&H Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands