NeoDen NeoDen10 User Manual Download Page 48

Page: 48 / 64

done.

P.S. If the offset is overly beyond 0.1mm, please kindly contact NeoDen support team.

2. function introduction:

Mark Left Position

: to use the left camera align the round mark

Mark Right Position:

to use the right camera align the round mark

Exit:

exit without operation

Save:

save the date after operation

Brightness:

the brightness of mark camera can be adjusted accordingly.

（

Note: the other three functions: memory position, correction position, right Mark calibration. These functions

are currently under development.

）

3. Nozzle and IC Camera central position



Nozzle 1 front IC camera Central Position: click to align, nozzle 1 will move to front IC camera and take photos. Once

the photo is displayed, to align the central position of nozzle with white crosshair and save the data.(P.S. Once setup

the Nozzle 1 front IC Central Position, nozzle 2-8 central position will be changed based on nozzle 1.) Apply the same

operation for remaining nozzle 2 to nozzle 8.



Nozzle 1 back IC camera Central Position: click to align, nozzle 1 will move to back IC camera and take photos. Once

the photo is displayed, to align the central position of nozzle with red crosshair and save the data.

Trash Box Position:

after Administration Login, click to align the position of trash box accordingly.

Placement Head Reset Position:

after Administration Login, click to align the position of Placement Head Reset

accordingly.

Exchange Nozzle Position:

after Administration Login, click to align the position of exchanging nozzles accordingly.

Summary of Contents for NeoDen10

































































Search results

Summary of Contents for NeoDen10

Reviews:

Related manuals for NeoDen10

Brands by name

Popular brands

NeoDen NeoDen10, User Manual

Search results

Summary of Contents for NeoDen10

Reviews:

Related manuals for NeoDen10

Brands by name

Popular brands