NEC POWERMATE VE - 07-1996 Manual Download Page 95 | Manualshive

Page: 95 / 152

background image

Setting System Parameters 4-17

Integrated Peripherals Parameters

FEATURE

OPTIONS

DESCRIPTION

Diskette
Controller

Enabled (default)
Disabled

Enables the on-board diskette drive
controller.

Local Bus IDE
Adapter

Both (default)
Disabled
Primary

Enables the on-board IDE controllers.
“Both” enables the primary (fast)
channel and secondary (standard)
channel. “Primary” enables only the
primary (fast) channel.

PS/2 Mouse

Enabled (default)
Disabled

Enables/disables PS/2-style mouse.

On-board
Sound

Stereo with SRS
(default)
Stereo
Mono

This parameter is only available when
the BIOS detects integrated audio on
the system board. When the audio is
detected, stereo with surround sound
is the default.

If playing an audio file with SRS
built-in, use the Stereo setting. Choose
Mono when stereo sound is not
desired.

THE SECURITY MENU

Selecting “Security” from the Main Menu displays a menu
with system security options.

NOTE

You can enter the Setup program with either

a User or Supervisor password. However, more
Setup choices are available with a Supervisor
password.

The User Password can only be set after setting a
Supervisor Password.

«
...
93
94
95
96
97
...
»

Summary of Contents for POWERMATE VE - 07-1996

























































































































































Reviews:

No comments

Related manuals for POWERMATE VE - 07-1996

Brand: NComputing Pages: 16

Brand: IBM Pages: 230

Brand: C&T Pages: 99

Brand: ASROCK Pages: 43

Brand: Avalue Technology Pages: 78

FieldGo PCATX-R9

Brand: BSi Pages: 40

DECstation 316+

Brand: DEC Pages: 94

eBOX625-842-FL Series

Brand: AXIOMTEK Pages: 60

Brand: Iron Age Office Pages: 7

Brand: Dell Pages: 54

Brand: Asus Pages: 8

Brand: Asus Pages: 38

Brand: Asus Pages: 28

Vivo AiO V222F Series

Brand: Asus Pages: 58

Brand: Asus Pages: 56

Vivo AiO V220 Series

Brand: Asus Pages: 66

Brand: Asus Pages: 56

Brand: Asus Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands