NEC POWERMATE VE - 07-1996 Manual Download Page 138

Page: 138 / 152

8-8 If You Have a Problem

Speaker Problems

Check the following problems to see the possible cause and
solution.

No sound from the speakers

Check that the speaker power is on.

Speaker volume is too low

Adjust the volume control on the speaker. If the volume
is still too low, adjust the volume through the system
software, see Chapter 6.

Sound is only coming from one speaker

Balance the speaker output by adjusting the balance in
the sound software, see Chapter 6.

Microphone Problems

Check the following problem to see the possible cause and
solution.

You get no response from the microphone

Check that the microphone is connected to the Mic In
connector on the back of your system.

Adjust the microphone (MIC) level through sound
software.

Summary of Contents for POWERMATE VE - 07-1996

























































































































































Search results

Summary of Contents for POWERMATE VE - 07-1996

Reviews:

Related manuals for POWERMATE VE - 07-1996

Brands by name

Popular brands

NEC POWERMATE VE - 07-1996, Manual

Search results

Summary of Contents for POWERMATE VE - 07-1996

Reviews:

Related manuals for POWERMATE VE - 07-1996

Brands by name

Popular brands