NEC POWERMATE VE - 07-1996 Manual Download Page 33

Page: 33 / 152

3-2 Installing Options

secondary cache

−

upgrade to a 256-KB asynchronous

or synchronous pipeline burst secondary SRAM cache
module (standard in some configurations).

drives

−

your system supports a total of four storage

devices. In addition to the standard 3 1/2-inch 1.44 MB
diskette drive, three other storage device slots are
available. Hard disk configurations come with a hard
disk drive installed and multimedia systems include an
installed CD-ROM reader.

OPTION INSTALLATION PROCEDURES

Installation instructions for the following options are
provided in this chapter.

expansion boards

SIMM memory upgrade

video memory upgrade

processor upgrade

L2 SRAM cache module (standard in some
configurations)

data storage devices

external options.

Summary of Contents for POWERMATE VE - 07-1996

























































































































































Search results

Summary of Contents for POWERMATE VE - 07-1996

Reviews:

Related manuals for POWERMATE VE - 07-1996

Brands by name

Popular brands

NEC POWERMATE VE - 07-1996, Manual

Search results

Summary of Contents for POWERMATE VE - 07-1996

Reviews:

Related manuals for POWERMATE VE - 07-1996

Brands by name

Popular brands