NEC POWERMATE VE - 07-1996 Manual Download Page 49

Page: 49 / 152

3-18 Installing Options

Checking System Memory

Use the following procedure to:

check the memory installed in the system

determine the SIMM configuration needed to increase
memory

NOTE

SIMM memory must be installed in pairs of

the same memory type.

identify SIMM sockets.

Locate the four SIMM sockets on the system board (see
“Option Installation Procedures” earlier in the chapter.

If any cables block access to the SIMM sockets, label
and disconnect them. If any boards block access to the
sockets, remove them.

Use the following table to determine the SIMM
configuration needed to upgrade memory and to identify
the sockets for SIMM installation.

Summary of Contents for POWERMATE VE - 07-1996

























































































































































Search results

Summary of Contents for POWERMATE VE - 07-1996

Reviews:

Related manuals for POWERMATE VE - 07-1996

Brands by name

Popular brands

NEC POWERMATE VE - 07-1996, Manual

Search results

Summary of Contents for POWERMATE VE - 07-1996

Reviews:

Related manuals for POWERMATE VE - 07-1996

Brands by name

Popular brands