NEC POWERMATE VE - 07-1996 Manual Download Page 45

Page: 45 / 152

3-14 Installing Options

Hold the slot cover support over the expansion board
bracket and replace the two screws removed earlier. The
slot cover support secures the expansion board in place.

Attaching the slot cover support

Attach any signal cables required by the expansion
board.

Replace the system unit cover.

Removing an Expansion Board

Remove the system unit cover as previously described.

Label and remove any cables connected to the board.

NOTE

To remove a board from an inside slot, see

“Removing an Expansion Board from the Inside
Slot.”

Screws

Expansion Board
Bracket

Slot Cover
Support

Summary of Contents for POWERMATE VE - 07-1996

























































































































































Search results

Summary of Contents for POWERMATE VE - 07-1996

Reviews:

Related manuals for POWERMATE VE - 07-1996

Brands by name

Popular brands

NEC POWERMATE VE - 07-1996, Manual

Search results

Summary of Contents for POWERMATE VE - 07-1996

Reviews:

Related manuals for POWERMATE VE - 07-1996

Brands by name

Popular brands