manualshive.com logo in svg

NEC MuPD78F0132H, User Manual

The NEC MuPD78F0132H product user manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and guidelines on operating and troubleshooting the product. With a user-friendly interface, users can easily access this invaluable resource to maximize their product experience.

Share
Download
background image

APPENDIX  D   LIST  OF  CAUTIONS 

User’s Manual  U16899EJ2V0UD 

524 

(10/24) 

Chapter 

Cl

assi

fi

cati

on 

Function Details 

of 

Function 

Cautions Page 

When TMHE0 = 1, setting the other bits of the TMHMD0 register is prohibited. 

p. 204

Soft 

TMHMD0: 8-bit  
timer H mode 
register 0 

In the PWM output mode, be sure to set 8-bit timer H compare register 10 
(CMP10) when starting the timer count operation (TMHE0 = 1) after the timer 
count operation was stopped (TMHE0 = 0) (be sure to set again even if setting 
the same value to CMP10). 

p. 204

Hard 

When the Ring-OSC clock is selected as the clock to be supplied to the CPU, the 
clock of the Ring-OSC oscillator is divided and supplied as the count clock.  If the 
count clock is the Ring-OSC clock, the operation of 8-bit timer H1 is not 
guaranteed (except when CKS12, CKS11, CKS10 = 1, 0, 1 (f

R

/2

7

)). 

p. 206

When TMHE1 = 1, setting the other bits of the TMHMD1 register is prohibited. 

p. 206

In the PWM output mode and carrier generator mode, be sure to set 8-bit timer H 
compare register 11 (CMP11) when starting the timer count operation (TMHE1 = 
1) after the timer count operation was stopped (TMHE1 = 0) (be sure to set again 
even if setting the same value to CMP11). 

p. 206

Soft 

TMHMD1: 8-bit 
timer H mode 
register 1 

When the carrier generator mode is used, set so that the count clock frequency of 
TMH1 becomes more than 6 times the count clock frequency of TM51. 

p. 206

Hard 

In PWM output mode, three operation clocks (signal selected using the CKSn2 to 
CKSn0 bits of the TMHMDn register) are required to transfer the CMP1n register 
value after rewriting the register. 

p. 212

Be sure to set the CMP1n register when starting the timer count operation 
(TMHEn = 1) after the timer count operation was stopped (TMHEn = 0) (be sure 
to set again even if setting the same value to the CMP1n register). 

p. 212

PWM output 

Make sure that the CMP1n register setting value (M) and CMP0n register setting 
value (N) are within the following range. 
00H 

≤

 CMP1n (M) < CMP0n (N) 

≤

 FFH 

p. 213

Do not rewrite the NRZB1 bit again until at least the second clock after it has 
been rewritten, or else the transfer from the NRZB1 bit to the NRZ1 bit is not 
guaranteed. 

p. 218

When 8-bit timer/event counter 51 is used in the carrier generator mode, an 
interrupt is generated at the timing of <1>.  When 8-bit timer/event counter 51 is 
used in a mode other than the carrier generator mode, the timing of the interrupt 
generation differs. 

p. 218

Be sure to set the CMP11 register when starting the timer count operation 
(TMHE1 = 1) after the timer count operation was stopped (TMHE1 = 0) (be sure 
to set again even if setting the same value to the CMP11 register). 

p. 220

Set so that the count clock frequency of TMH1 becomes more than 6 times the 
count clock frequency of TM51. 

p. 220

Set the values of the CMP01 and CMP11 registers in a range of 01H to FFH. 

p. 220

In the carrier generator mode, three operating clocks (signal selected by CKS12 
to CKS10 bits of TMHMD1 register) or more are required from when the CMP11 
register value is changed to when the value is transferred to the register. 

p. 220

Chapter 8 

Soft 

8-bit 
timers H0, 
H1 
(TMH0, 
TMH1) 

Carrier 
generator mode 
(TMH1 only) 

Be sure to set the RMC1 bit before the count operation is started. 

p. 220

 

Summary of Contents for MuPD78F0132H





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MuPD78F0132H

Newport MM4005 User Manual preview
MM4005
Brand: Newport Pages: 417
ZiLOG Z8 Encore! XP Dual F1680 Series User Manual preview
Z8 Encore! XP Dual F1680 Series
Brand: ZiLOG Pages: 18
Danfoss AME 56K Instructions Manual preview
AME 56K
Brand: Danfoss Pages: 10
Partlow MIC 1161 Operator'S Manual preview
MIC 1161
Brand: Partlow Pages: 49
Ascon tecnologic TLB 55 Operating Instruction preview
TLB 55
Brand: Ascon tecnologic Pages: 11
ROBOT3T THC3T-02 Operation Manual preview
THC3T-02
Brand: ROBOT3T Pages: 21
StudioComm Dante 792 User Manual preview
Dante 792
Brand: StudioComm Pages: 61
HANYOUNG NUX TPR-3N Instruction Manual preview
TPR-3N
Brand: HANYOUNG NUX Pages: 4
LEGRAND MRD6 v2 Installation Instructions Manual preview
MRD6 v2
Brand: LEGRAND Pages: 10
Continental Instruments CICP1800T Datasheet preview
CICP1800T
Brand: Continental Instruments Pages: 2
H3C WX2880X Installation Manual preview
WX2880X
Brand: H3C Pages: 48
Fairchild HPD1***A**K*N Installation, Operation And Maintenance preview
HPD1***A**K*N
Brand: Fairchild Pages: 4
S+S Regeltechnik HYGRASREG KH-10 Operating Instructions, Mounting & Installation preview
HYGRASREG KH-10
Brand: S+S Regeltechnik Pages: 16
Harmonic Drive YukonDrive-1021 Operating Manual preview
YukonDrive-1021
Brand: Harmonic Drive Pages: 53
Xpelair FR22-30 and Installation And Operating Instructions Manual preview
FR22-30 and
Brand: Xpelair Pages: 20
Carrier i-Vu MPC Open XP IO48/816 Installation And Startup Manual preview
i-Vu MPC Open XP IO48/816
Brand: Carrier Pages: 50
Jetter JC-975MC Installation Manual preview
JC-975MC
Brand: Jetter Pages: 28
Regin OPTIGO OP5 Manual preview
OPTIGO OP5
Brand: Regin Pages: 24

Brands by name

Popular brands

Load more brands