manualshive.com logo in svg

NEC MuPD78F0132H, User Manual

The NEC MuPD78F0132H product user manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and guidelines on operating and troubleshooting the product. With a user-friendly interface, users can easily access this invaluable resource to maximize their product experience.

Share
Download
background image

APPENDIX  D   LIST  OF  CAUTIONS 

User’s Manual  U16899EJ2V0UD 

518 

(4/24) 

Chapter 

Cl

assi

fi

cati

on 

Function Details 

of 

Function 

Cautions Page 

Set a value other than 0000H in CR00n in the mode in which clear & start occurs 
on a match of TM0n and CR00n. 

p. 140

Soft 

If CR00n is cleared to 0000H in the free-running mode and in the clear mode 
using the valid edge of the TI00n pin, an interrupt request (INTTM00n) is 
generated when the value of CR00n changes from 0000H to 0001H following 
TM0n overflow (FFFFH).  In addition, INTTM00n is generated after a match 
between TM0n and CR00n, after detecting the valid edge of the TI01n pin, or 
the timer is cleared by a one-shot trigger. 

p. 140

When the valid edge of the TI01n pin is used, P01 or P06 cannot be used as the 
timer output pin (TO0n).  When P01 or P06 is used as the TO0n pin, the valid 
edge of the TI01n pin cannot be used. 

p. 140

Hard 

When CR00n is used as a capture register, read data is undefined if the register 
read time and capture trigger input conflict (the capture data itself is the correct 
value).  If a timer count stop and a capture trigger input conflict, the captured data 
is undefined. 

p. 140

CR00n: 16-bit 
timer 
capture/compare 
register 00n 

Do not rewrite CR00n during TM0n operation. 

pp. 140, 
153, 
158, 
170 

Soft 

If the CR01n register is cleared to 0000H, an interrupt request (INTTM01n) is 
generated when the value of CR01n changes from 0000H to 0001H following 
TM0n overflow (FFFFH).  In addition, INTTM01n is generated after a match 
between TM0n and CR01n, after detecting the valid edge of the TI00n pin, or the 
timer is cleared by a one-shot trigger. 

p. 141

Hard 

When CR01n is used as a capture register, read data is undefined if the register 
read time and capture trigger input conflict (the capture data itself is the correct 
value).  
If count stop input and capture trigger input conflict, the captured data is 
undefined. 

p. 141

CR01n: 16-bit 
timer 
capture/compare 
register 01n 

CR01n can be rewritten during TM0n operation.  For details, see Caution 2 in 
Figure 6-20. 

p. 141

TMC0n: 16-bit 
timer mode 
control register 
0n 

16-bit timer counter 0n (TM0n) starts operation at the moment TMC0n2 and 
TMC0n3 are set to values other than 0, 0 (operation stop mode), respectively. Set 
TMC0n2 and TMC0n3 to 0, 0 to stop the operation. 

p. 142

Timer operation must be stopped before writing to bits other than the OVF00 flag.  p. 143

Set the valid edge of the TI000/P00 pin using prescaler mode register 00 
(PRM00). 

p. 143

TMC00: 16-bit 
timer mode 
control register 
00 

If the following modes: the mode in which clear & start occurs on match between 
TM00 and CR000, the mode in which clear & start occurs at the TI000 pin valid 
edge, or free-running mode is selected, when the set value of CR000 is FFFFH 
and the TM00 value changes from FFFFH to 0000H, the OVF00 flag is set to 1. 

p. 143

Timer operation must be stopped before writing to bits other than the OVF01 flag.  p. 144

Set the valid edge of the TI001/P05 pin using prescaler mode register 
01(PRM01). 

p. 144

Chapter 6 

Soft 

16-bit 
timer/ 
event 
counters 
00, 01 
(TM00, 
TM01) 

TMC01: 16-bit 
timer mode 
control register 
01 

If the following modes: the mode in which clear & start occurs on match between 
TM01 and CR001, the mode in which clear & start occurs at the TI001 pin valid 
edge, or free-running mode is selected, when the set value of CR001 is FFFFH 
and the TM01 value changes from FFFFH to 0000H, the OVF01 flag is set to 1. 

p. 144

 

Summary of Contents for MuPD78F0132H





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MuPD78F0132H

ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Brand: ABB Pages: 4
Particle B Series Quick Start Manual preview
B Series
Brand: Particle Pages: 6
ECKELMANN VS 3010 BS Operating Instruction preview
VS 3010 BS
Brand: ECKELMANN Pages: 178
H3C WX Series Registration And Activation Manual preview
WX Series
Brand: H3C Pages: 17
H3C WX Series Getting Started Manual preview
WX Series
Brand: H3C Pages: 32
Federal Signal Corporation ultravoice UV Installation, Operation And Service Manual preview
ultravoice UV
Brand: Federal Signal Corporation Pages: 79
Federal Signal Corporation PAGASYS GEN II Description, Installation, And User Manual preview
PAGASYS GEN II
Brand: Federal Signal Corporation Pages: 32
Häfele 633.03.298 Operating Instructions Manual preview
633.03.298
Brand: Häfele Pages: 24
W.E.ST. SCU-138-P Technical Documentation Manual preview
SCU-138-P
Brand: W.E.ST. Pages: 34
Ltech TT-DX-R4-5A Manual preview
TT-DX-R4-5A
Brand: Ltech Pages: 4
Motor Guard M-60R Instructions preview
M-60R
Brand: Motor Guard Pages: 2
GEM DG-2000 Series Operation Manual preview
DG-2000 Series
Brand: GEM Pages: 17
YASKAWA CIMR-VC*****H**-00 series Quick Start Manual preview
CIMR-VC*****H**-00 series
Brand: YASKAWA Pages: 32
aerl CoolMax SRX Installation And Operation User Manual preview
CoolMax SRX
Brand: aerl Pages: 27
Kelly KLS4812S User Manual preview
KLS4812S
Brand: Kelly Pages: 32
NDS SUNCONTROL2 User Manual preview
SUNCONTROL2
Brand: NDS Pages: 20
M-Audio Keystation 61es User Manual preview
Keystation 61es
Brand: M-Audio Pages: 15
METRON FD4 Manual preview
FD4
Brand: METRON Pages: 34

Brands by name

Popular brands

Load more brands